How can an adaptive fuzzy sliding model be designed for a highly nonlinear system with multiple singular control points?

Farzad Tat Shahdost @Farzad-Tat-Shahdost

28 May 2021 0 9K Report

Badges
Science topic

Similar topics
Medicine
Epi
Epidemics

More Farzad Tat Shahdost's questions See All

How to get "density" and "viscosity" for cavitation(water vapor) for cavitating Francis turbine?

Hello there I am simulating cavitation for a Francis turbine. Francis turbine is rotating with 826 rpm. I have two questions; 1- Vapor pressure for my case is 2100 Pascal, and Temperature is 25...

13 May 2024 4,403 7 View

How to avoid segmentation in Level Set Topology Optimization ( I would need to localize the variation of the level-set)?

Dear All, I am trying to converge on an optimal solution for a compliance minimization problem using a parametric RBF-based level set method. However, I have faced the following problem(s) for...

14 February 2024 9,511 0 View

How to model anchored cable bolts (passive bolts) in FLAC 2D 8.1 software?

I am investigating the impact of pretension effect around circular tunnels. How can I do my own modeling? 1- I want to excavate a tunnel. 2- I want to put a rock bolt or cable bolt in the hole 3-...

08 February 2024 7,166 1 View

What are the boundary conditions for a 2D Channel when we know pressure inlet?

Hello everyone I am working in a 2D channel where I know the inlet Pressure as a function of cosine, and out let pressure at atmospheric level. What should I use for inlet and outlet boundary...

26 November 2023 6,412 5 View

How can I have smooth boundaries in topology optimization using level-set method?

I am working on topology optimization using the parametric level set method. Regardless of the methodology, I thought it might be a generic problem in Topology optimization with which many...

05 October 2023 2,725 4 View

How to prepare a distribution map of Fritillaria genus in the world?

Fritillaria is one of the largest genera of the Liliaceae family. There are about 170 taxa of this genus all over the world. These are mostly native to the temperate regions of the Northern...

03 July 2023 5,678 0 View

Can I use convergence behavior of residuals to predict if my flow is laminar or turbulent when I use steady state simulation?

Hello all, I am trying to predict Drag coefficient of an object(and I am not interested in the vortex shedding after my object, also I cant afford LES), so I decided to use steady state...

05 April 2023 1,357 0 View

laminar Flow over a sphere(laminar vs KOmegaSST simulation) in OpenFoam?

Hello all I am simulating flow over a sphere at Re = 881 where Drag coefficient must be almost Cd=0.5. I simulate it using both using laminar and Turbulent models(KOmegaSST). for laminar...

11 March 2023 9,341 3 View

How to calculate energy spectrum for a Homogenous Isotropic turbulence at specific time in a rectangular shape?

Hello all I have two questions; 1- First of all, is it possible to generate HIT inside a rectangle? If so, it is called HIT again? 2- if Nx=Nz but Ny is different, How can I calculate power...

12 January 2023 3,135 3 View

How to use Linear forcing for generating HIT(Homogeneous Isotropic Turbulence)?

Hello everyone I have read Lundgren(2002) article "Linearly forced isotropic turbulence" which by adding a linear forcing to momentum equation, he was able to get forced isotropic turbulence. I...

08 January 2023 4,546 2 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

I need a reliable source or an example supported by excel sheet to understand Fuzzy Vikor?

27 July 2024 5,916 1 View

Look for qualified candidates of Visiting Scholars to Southwest Jiaotong University?

We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...

20 July 2024 1,165 1 View

How to combat antibiotic resistance?

The increasing resistance of bacteria to antibiotics has made many infections difficult to treat, posing not only a threat to public health but also a major challenge to healthcare systems worldwide.

18 July 2024 6,688 3 View

How to prepare bacterial conditioned media to study the effect of bacterial secretome?

I would like to investigate the effect of bacterial secretome on cancer cells. How do you prepare conditioned media from bacteria?? conditions- time points - media I am looking for the best way...

17 July 2024 3,785 9 View

How can the resilience of agricultural systems be improved by both gradual climate change and increased climatic variability and extremes?

17 July 2024 3,681 3 View

How to model a non-minimum phase system?

In deriving a model of an LTI dynamic system, the model of the system does have no RHP zeros, however, when inspecting the step response, it reveals a non-minimum phase system represented by a...

14 July 2024 6,355 2 View