Hi Please any one can guide me or can share his experience if he used ethylene glycol as a solvent to prepare nanofibers by using electrospinning?

10 October 2016 1 5K Report

I want to prepare nanofibers for some semiconductor material that are easily soluble in Ethylene Glycol?

you can follow this Article in RSC Advances 5(118) · November 2015

DOI: 10.1039/C5RA14897A: Tunable properties of GO-doped CoFe2O4 nanofibers elaborated by Electrospinning. but I use ethanol as a solvent, because it is easy to evaporate

Badges
Science topic

More Muhammad Shahid's questions See All

What will be the absorption band edge and bandgap if we combine two semiconductor oxide materials to form a hetero-structure?.

For example if we make a composite of SnO2 and ZnO. Than whats about the absorption band edge and bandgap of their heterostructure. Is it necessary that the absorption band edge of the...

04 May 2017 3,274 3 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

¿Are oxygen vacancies in semiconductors capable to change the band gap?

Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...

30 July 2024 8,339 2 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

How can I immobilize Glutathione on to PCL electrospun nanofiber?

Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or...

18 July 2024 9,725 1 View

How can I quantify MDEA (N-Methyldiethanolamine) with a GC-FID?

I have a mixture of glycol, water, MDEA, and piperazine. I want to analyze it with GC-FID.

15 July 2024 9,652 3 View

How can I quantify MDEA (N-Methyldiethanolamine) with a GC-FID?

I have a mixture of glycol, water, MDEA, and piperazine which I want to analyze with GC.

15 July 2024 2,181 10 View

How to quantify fibrin formation for absorbent hemostatic biomaterial ?

I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...

08 July 2024 3,714 1 View

What is the best software for simulation of mode locked diode laser?

Hi Dear All I would like to simulate a mode locked semiconductor laser. Does anyone know what is the best software to do it?

06 July 2024 1,648 4 View

Why PLLA deposited by gap electrospinning lose piezoelectricity?

I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...

17 June 2024 9,763 0 View