Hi Everyone, i am trying to do a sealing analysis(static). The seals roll due to which i cannot apply fluid pressure. Are there any subroutines?

09 May 2016 1 4K Report

The surfaces which are exposed to fluid keeps on changing continuously during the analysis. hence are there any methods which would address the problem?

Shiuh-Hwa Shyu

Can you be more specific?

Badges
Science topic

More Sumit Sharma's questions See All

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

RNA-seq DEGs downstream analysis and reporting in literature?

I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...

23 February 2021 8,969 1 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

Can someone help me with this error that I am getting while estimating a VAR model in R?

I am using annual time series data to estimate a VAR model in R. However, when I run the command to find the optimal lag length, I get the following error: Fehler in VARselect(data, lag.max = 10,...

18 February 2021 9,647 3 View

Why at farmer level Cow/Buffalo are not done artificial insemination just after 2 month for yearly calving?

Physiologically in cow, oestrous heat again goes on the peak after 2 months but locally this is not observed and AI is after two months but done after at least 6 months.

17 February 2021 685 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View