31 August 2016 3 2K Report

hey 

I was wondering if it is possible to use HDV ribozyme at the 5' end instead of hammerhead ribozyme? and how to design the 5' end for that purpose.

thanks. 

More Najib Abdellaoui's questions See All
Could we apply a strict carnivorous diet for laboratory mice or rats?

hello, a protocol requires a strict carnivorous diet for laboratory animals, can this diet be applied to mice and rats for 2 months (cheese, cooked chicken meat, eggs + vitamins in water)? thank you

06 January 2021 4,066 3 View

How to link Research Gate article citations to Google Scholar ?

Some publications which we upload in Research Gate receives citations but the same paper which has been listed in the Google Scholar doesn't show any citation .

01 January 2021 908 5 View

Calculation of dilution factor for fumonisin extracted rice cultured with fusarium species?

hello I would like to ask for help regarding calculation of dilution factor to get the amount of mycotoxin per gram of sample. the extraction protocol as fellow: -ground 5 g of sample with 25 mL...

29 November 2020 1,831 15 View

Could the hepatic catalase activity increases when we treat mice with immunostimulants?

hello, I would like to know please, if there are cases in which we can observe an increase of catalase activity in mice treated with a therapeutic dose of immunostimulants? I did twice the...

28 September 2020 4,193 3 View

How to calculate the amount of toxin per gram of wheat?

hello, I am working on the extraction of trichothecenes from the grain of wheat and I would like to ask how is it possible to calculate the concentration of toxin ug per gram of wheat? the...

17 March 2020 7,469 3 View

How I can get source code for 802.11a PHY layer in matlab without using simulink?

How I can get source code for 802.11a PHY layer in matlab without using simulink?

27 December 2019 2,191 3 View

Please someone tell me about IC50 on radical scavenging assay?

I've been measured the percent of my concentration series (R2 = 0.998) but the data weren't covered value more than 50%. Should I repeat my experiment or I just extrapolate the regression...

29 July 2019 2,899 5 View

What are the limitations for colorimetric in computer vision technique to extract object features with noisy background?

Combination of morphometric and colorimetric has been applied for feature extraction in detection algorithm. In noisy background, this CV technique facing wrong identification results as well as...

20 August 2018 845 6 View

How to validated the free radical inhibition on the following equation?

Dear All, I have find the different equation as usually to use for dpph inhibition on extract. How to validate the result that the equation was correct Please check the equation formula on the...

03 May 2018 1,394 5 View

What is the difference between Distributed based RAN (D-RAN) and Fog based RAN (F-RAN)?

In cloud-based RAN (C-RAN), all the signal processing were transferred from the local or small cell base stations (i.e. Distributed D-RAN) to a centralized center to simplify the network...

05 February 2018 2,941 3 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Which of the Covid-19 Vaccines would elicit the best immunoprotection and why?

I want to know which of the available Covid-19 Vaccines would elicit the best immunological response and why

02 March 2021 1,388 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close