Help please help on FEA?

05 April 2017 0 1K Report

Help please. On modeling a machine in Ansys Maxwell 3D (transient solver) I got this error message when I try to validate my design

Verify conduction path 'Path1': There can only be one internal coil terminals for any conduction path.

Badges
Science topic

Similar topics
Psychology

More Omokhafe James Tola's questions See All

Can someone explain to me or provide me some material about a step by step procedure of simulating a butt-welded fusion of two HDPE pipes in ABAQUS?

I am trying to simulate a butt-welding for the fusion of two HDPE pipes. I have modeled the pipes in the ABAQUS. I have also created a heat transfer step in which the heat from the heating plate...

20 September 2022 8,019 0 View

Looking to collaborate?

My post today is directed to registered nurses from Ethiopia, Ghana, Kenya, and South Africa. I am interested in collecting research data from the African countries listed above. Thus, I would...

05 September 2021 5,084 4 View

Does the vaccine have effect on covid-19 diagnosis (RNA, antigen or antibody)?

Nowadays, many methods were used for covid-19 diagnoses like RT-PCR, antigen, or antibody test. Despite its unaffordability, the RT-PCR remains a confirmatory one. As a point of care, either...

23 March 2021 3,416 5 View

I need to put 15 sec delay to my push button, that activate a contactor to controll other machine?

Figure attached, to get your support how to delay a push button using analog timer.

20 February 2020 8,161 3 View

How can I can correct Communication failure error under ANSYS Maxwell?

While running a 2D Maxwell on single phase electric machine and this error message appeared: Communication failure. System error no: 109, error description: Unknown error Please I need help on...

11 September 2018 9,052 1 View

What is the best way to re-suspend amyloid beta (AB1-42)?

Hi , Please can you share you experience or expertise skill on how to re-suspend amyloid beta(AB42) that will be soluble? NB- if you use 1,1,3,3-Hexafluoro-2-propanol(HFIP), what grade and...

22 August 2018 1,705 4 View

How can I perform Co-Simulation of PMSM using Ansys Maxwell and Simplorer?

Dear all. Am working on three-phase PMSM using Ansys Maxwell and Simplorer. I created the design in2D Maxwell and trying to co-simulate with Simplorer by adding the converter using external...

23 October 2017 8,145 3 View

Is Quantum Efficiency(QE) same as IPCE(Incident Photon to Current Efficiency) or APCE(Absorbed Photon to Current Efficiency) for DSSCs?

I've seen sources that say it's the same as IPCE while others say it's the same as APCE

13 January 2015 2,359 6 View

Instructional technology for teaching and learning

WHY DO WE NEED TO HAVE AN INSTRUCTIONAL TECHNOLOGY MODEL FOR EDUCATION? CAN YOU LIST SOME INSTRUCTIONAL TECHNOLOGY MODELS YOU KNEW IN YOUR STUDY? THANK YOU FOR YOUR HELP!

01 January 1970 1,442 10 View

Effect size in reporting research results

As far as the effect size in research is very important SPSS can not calculate it directly. I want to use the effect size calculators that find on https://lbecker.uccs.edu/. Can I believe that the...

01 January 1970 3,906 6 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View