Hello. I want to crosslink using natural or synthetic polymers. I need an elastic and highly biocompatible polymer. Could you help ?

More Efe Küçükgüçlü's questions See All

What is the best material contact to use on cubic boron Nitride film on a yellow diamond substrate for Van der Pauw measurement?

Researchers studying the electrical properties of cubic boron nitride (cBN) films on diamond substrates encounter several challenges. One major issue is achieving high-quality deposition of cBN...

03 May 2024 8,448 0 View

Reducing the number of integer digits of the variable in VECM analysis?

With VECM analysis, I examine the relationship between the spot market price volatility of the shares and the volumes of the futures contracts on which these shares are based. I have a problem in...

21 March 2023 1,355 4 View

Critically evaluate cognitive theories of object recognition?

To answer this question, you should define what is meant by object recognition. You can then include research evidence showing how object recognition is performed.

28 October 2021 8,625 4 View

How do I determine the gas sensing properties of sulphides?

Over the years, i have realized sulphides of ternary thin films are not good materials for gas sensing but oxides definitely are good sensing materials. What could be the cause of not using...

03 April 2020 2,054 4 View

I want to use a UVC lamp to sterilize disposable masks and make them reusable? for covid 19 ?

Im going to buy 36 watt omron brand UVC lamb.I need to learn the optimal distance and time that I have to put the masks on it to reach 60 mJ / cm2 energy with this lamp. 36w uvc bulb means 36...

25 March 2020 2,288 7 View

Why do we observe orange eyed drosophila in the F2 progeny that we should not observe it in the Morgan's experiment?

plz give me reliable sources

01 April 2017 9,089 1 View

Which phases are critical in making structural equation modeling with population (not sampling)?

I have a population N=80. Because i do not have a sample is there a problem about sample size? And any critical thing that i pay attention different from sem with a sample? Shortly. how to do...

29 February 2016 2,278 5 View

What are the metrics to measure energy efficiency in cognitive radio networks?

how is energy efficiency in cognitive radio networks measured?

08 November 2015 8,315 5 View

How can energy efficiency be improved in all spectrum sensing stages of cognitive radio networks?

Is there any way we can improve energy efficient transmission in a cooperative cognitive radio network? what are the solutions of maximizing energy efficiency in the local sensing stage, result...

10 February 2015 7,125 1 View

How can we possibly use cooperative spectrum sensing in reducing PUEA (Primary User Emulation Attacks) in a cognitive radio network?

See above

26 May 2014 6,854 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

Why is it not common to see similar pairs in polymer sliding pairs?

If the pairs are similar, will it reduce the adhesion due to electric charges?

29 July 2024 3,185 2 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

What is the difference between coordination polymer, MOFs, MCOFs?

Wherever I have referred, it puts me in a dilemma about the exact differences between these. It would be really helpful if someone can put me out of this trouble.

21 July 2024 3,045 3 View

Dmitriy Berillo

Hello,

If you chose covalent cross-linking of amine containing polymer then I suggest to use dextran polyaldehyde, which does not have such drawback as glutaraldehyde, due to high molecular weight. Please have a look the ref. Oxidized gextran and gelatin. Article Preparation and physicochemical characteristics of cryogel b...

Roman Morschhaeuser

Dear Efe,

Poly (ethylene glycol) diglycidyl ether is a good crosslinking agent. There are different molecular weight ranges available. PEG units should be highly biocompatible and elastic.

Regards,

Roman