Has anyone used a UART to WiFi module?

More Arjav Bavarva's questions See All

How can I set up serial communication between Atmega16L and PC?

I connect serial tx pin no 18 to RS232 converter and give it to PC. Hyperterminal should display transmitted string but it is not coming. RS232 is working as I checked loopback. Atmega is also...

26 March 2015 9,230 11 View

Which video compression technique is the best for wsn?

Can any one tell me which algorithm is used for video compression in wsn? What is the compression rate?

09 February 2015 8,686 6 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How to increase coupling range (distance between reader and sensor coils) in LC resonance circuit?

Hello great researchers, I am working on a wireless pressure monitoring project where sensing part is actually an LC resonance sensor and I am using a planar coil as a reader to get wireless...

11 February 2021 4,148 5 View

Inductive wireless power transfer in electrical vehicle battery charging requirements?

Dear sir In wireless charging electrical vehicle design, what are the basic requirements and what are standards are taking. In world wide or Indian standard what are the specification, please...

25 January 2021 722 2 View

What are the research gaps in inductive wireless power transfer in ev battery charging?

Dear sirs/,madams, I want research gaps,objectives and issues in inductive wireless power transfer in ev battery charging. Any one please help me

14 January 2021 7,466 2 View

FSK modulation/demodulation with Fc=10MHZ to achieve a minimum 128kbps baud rate?

I would like to modulate and demodulate a binary stream of data at 128kbps baud rate using BFSK or N-FSK with carrier freq. of around 10 MHz. I have the following questions? 1) What is the...

12 January 2021 4,497 4 View

Are there other models that meet the same purpose?

Both Jakes and Gaussian models are used to characterize the power spectral densities of mobile communication channels.

11 January 2021 759 3 View

Is there anyone who can suggest some related work based on HMM implementation for routing protocol in WSNs?

I'm trying to solve the energy issue conservation in WSNs and I want to use the Markov technique to predict this conservation and demand the routing protocol to select an optimal path among a...

05 January 2021 1,994 2 View

Why mutual inductor takes high current at no load condition?

I simulate an inductive wireless power transfer system in matlab. I set the primary and secondary mutual inductor resistance is 0.3ohm. So when i run the circuit it took high current at no load...

29 December 2020 9,536 3 View

1.How can put nodes on equal distance in WSN? 2.How calculate retransmission of each node in WSN? 3.How to create buffer for each node?

I am using matlab simulator and doing paper selfish node detection based on average retransmission number. Some factors determine selfish node in wsn -If energy is not sufficient to forward...

28 December 2020 7,294 2 View

Rohit Rangwani

Yes a little bit of configuration is required.Here is one link I found containing detailed procedure to be followed

http://www.linksprite.com/pub/tutorial/wifi_uart_tutorial.pdf.

Almost similar procedure is required for all.

Dilraj Nadarajan

If you are using arduino board, this tutorial will help you

http://www.arduino.cc/en/Guide/ArduinoWiFiShield