I want to electrodeposite metal oxide, say MnO2 on a Carbon current collector.What are the different techniques?

I want to electrodeposite metal oxide, say MnO2 on a carbon current collector.What are the different techniques? How to decide the potential window for the electrodeposition? I have consulted...

04 March 2018 6,313 3 View

How the functional groups of reduced graphene oxide effect the electrochemical performance of a supercapacitor in ionic liquid electrolyte (EMIMTFSI)?

08 September 2017 5,026 4 View

In one of my Western blot results all my protein bands (33- 57 kDa) appeared at the top (protein marker was fine) 175 to 270 kDa. Reason?

I guess that the reducing sample buffer might have expired so that the b-mercaptoethanol is no longer stable which in turn did not result in reduction and the proteins could not migrate properly...

21 May 2017 1,151 5 View

What are the criteria of selection of proteins for western blot validation after global proteome analysis?

09 July 2016 1,929 3 View

What should be the degassing temperature of Graphene for BET surface area measurements?

Please help me find the answer.

04 November 2014 3,696 4 View

What is the function of Mo in AMoO4 type compound (A= Ni, Mn, Co) in enhancing electrochemical performance in aquous Na2SO4 electrolyte?

Can anyone help me find the answer?

15 September 2013 9,254 2 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Which software is best to analyse multi-phase fluid flows ?

Hello everyone, hope all is good. I want to analyse multi-phase fluid flow through pipe, which software is best to do so ?

21 February 2021 4,230 8 View

What is difference between In-line transmission (%) and Total transmission (%) value of optically transparent Ceramics?

I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...

20 February 2021 9,405 6 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

How to calculate the internal pressure of a riser pipe?

I am designing a riser pipe for use in ocean down to depths of 5km. Polymetallic nodules are pumped from the seabed to the surface. For my FEA and CFD analyses I need to input a maximum pressure...

06 February 2021 2,803 3 View

Sample preparation for ceramics i.e. iron silicate (fayalite), iron oxides, alumina, spinel mineral (hercynite)?

Recommendations in preparing ceramics for nanoindentation and in the process minimize introducing stresses from sample preparation i.e. polishing stage.

02 February 2021 6,211 3 View

What should I do if the reviewer couldn't finalize the review in the journal's given time?

I have Submitted 2,3 Papers in Science Direct associated Journals but the time of the first decision has been ended so What should I do? Could I email them to remind them about the first decision?

01 February 2021 5,788 7 View

What are the thermodynamic and kinetic similarities and differences among dendrite formation during solidification of metals, ceramics and polymers?

Basic dendrite formation of metallic alloys are explained by thermal and constitutional degree of supercooling and most-supercooled band of liquid somewhat ahead of solidification front that...

30 January 2021 8,450 2 View

Is my beginners approach to ansys fluent udf implementation realistic?

Hello dear online comunity, i am new to CFD and we are currently involved in a project work for our masters degree. Since the problem we decided to simulate is quite complex, we cannot rely on the...

29 January 2021 2,200 3 View

Why can't ANSYS Mechanical APDL detect the volume of my design ?

The 1st image shows the moment when I import my design(IGES) into the Mechanical APDL. The 2nd image occurs when I wanted to Operate>Boolean>Divide Volume By Area. The design is a regular...

28 January 2021 2,962 3 View