17 June 2018 6 10K Report

Is it possible to do Frequency Response Analysis of a nonlinear system in ANSYS Workbench?

More Abdullah Al Masud's questions See All
Can we mark 'EFL Learners shifting from general digital to AI technologies' as technological transition?

After COVID-19 it has seen that EFL learners technological affiliation has raised. In addition, in the post-COVID period learners started to engage AI technologies like ChatGPT while learning...

08 August 2024 8,964 4 View

How to generate a citation of my paper from ResearchGate?

How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...

08 August 2024 6,690 3 View

Does Anyone have expertise in in vitro transcription and RNA pull down assay?

I am currently working on LncRNA; to know the lncRNA-protein interactions I want to do RNA pull down assay, so I need to design primers with T7 promoter. I need assistance in this regard.

07 August 2024 6,622 1 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,291 2 View

How can I add own Henry coefficients in Aspen Plus?

Hi, i would like to simulate an absorption process in Aspen Plus. I want to use the NRTL model und would like to add some individual Henry coefficients. Is that possible and how?

05 August 2024 2,333 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Can usage of AI tools like chat GPT in research work is recommendable ?

AI tools like ChatGPT can enhance research work significantly when used responsibly and in conjunction with thorough human oversight.

05 August 2024 1,842 3 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

ANY free software for reconstructing neurons in the microscopic image?

Hi everyone, I am working on brain slices for visualizing a protein in the soma and dendrites, using a fluorescence tag. However, I need a tool (not paid) for reconstruction of the whole neuron,...

04 August 2024 4,725 2 View

Similar questions and discussions
Could you recommend some articles on Urban Transportation System optimization and Innovation?

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Look for qualified candidates of Visiting Scholars to Southwest Jiaotong University?

We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...

20 July 2024 1,165 1 View

How to combat antibiotic resistance?

The increasing resistance of bacteria to antibiotics has made many infections difficult to treat, posing not only a threat to public health but also a major challenge to healthcare systems worldwide.

18 July 2024 6,688 3 View

How to prepare bacterial conditioned media to study the effect of bacterial secretome?

I would like to investigate the effect of bacterial secretome on cancer cells. How do you prepare conditioned media from bacteria?? conditions- time points - media I am looking for the best way...

17 July 2024 3,785 9 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close