For transmitting the torque of 7000 Nm and 300 rpm, how much angle can propeller shaft can be set Max between two mountings ?

Manikandan Rajaraman @Manikandan_Rajaraman

15 September 2023 0 6K Report

Need to understand the maximum angle of propeller shaft when it is mounted for transmitting torque of 7000 Nm with 300 rpm. As we can not assembling it in straight axis and require more than 70 deg. Is it ok to do with this angle ?

Badges
Science topic

Similar topics
Correction

More Manikandan Rajaraman's questions See All

How to size the driving motor for gear test rig in terms of torque requirement ?

Is motor should capable enough to cater the required input torque to gear subjected to test or can it be less, since the loading mechanism is different

01 September 2016 2,033 1 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

How is the bacterial genome's high protein count verified as genuine despite 800+ contigs and good metrics (98.55%completeness, 0.68% contamination)?

Given that the bacterial genome has over 800 contigs, but its quality metrics are good, with a completeness of 98.55% and a contamination of 0.68% as assessed by CheckM, what specific validation...

01 August 2024 1,514 1 View

How to know the b axis of a single crystal?

How to apply magnetic field parallel to b axis of any crystal

29 July 2024 4,083 2 View

MAGeCK Plotting Error: Logarithmic Axis Must Have Positive Limits?

I have been running a MAGeCK test command on the terminal for a CRISPR screen to rank sgRNAs and genes based on the read count tables. However, I get only the plot of the top-ranked genes...

28 July 2024 9,811 1 View

How can I define Planetary motion in ABAQUS CAE, how define motion of three rollers around a central axis and passive rotation about their own axis?

16 July 2024 4,145 1 View

I came across oscillations in a pressure profile for a pipeline flow along the axis of a cylinder, how do I prove that these are not numerical err?

In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?

13 July 2024 6,296 5 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

Cloning 1334 bp insert into 6.1kb vector using HiFi DNA assembly/Gibson assebmly cloning ?

Hello, I am trying to clone 1334 bp insert into 6.1 kb vector using HiFi DNA assmebly/Gibson assembly kit. I am taking 100ng of vector and 1:5 molar ratio of vector: insert and 4 hrs of...

27 June 2024 9,652 2 View

How to reduce the material coming out of the torque rheometer?

A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....

25 June 2024 10,154 0 View

To do gibson assembly cloning can I use DH5alpha strain of E. coli. for transformation?

20 June 2024 774 1 View