Fatal error when using pdbgmx to run NRAS bound with GTP using GROMACS 4.6.7?

I have tried to run simulation for protein complex of NRAS(5UHV) bound with Mg and GTP. However I have encountered the following error while using pdb2gmx: Program pdb2gmx, VERSION...

18 December 2019 2,246 3 View

How to get vehicle count and dataset from any one Toll plaza in India, or my research?

I wish to collect real time traffic in India. Is it feasible to get such data through any toll gate ?

04 May 2019 8,521 3 View

What is the best method to mass rear rice yellow stem borer?

Dear delegates I wish to get some information on rearing techniques of rice yellow stem borer. I started doing the same on natural host. But i face difficult and also feel cumbersome in doing mass...

02 July 2017 9,959 25 View

How to solve mixed level design in Minitab 17?

To Solve mixed level design with 3 factors and factor 1(6 level), factor 2(5level), factor3(4-level), I have used Minitab general design Full factorial -with 2 replications, totally 240...

01 February 2017 9,282 9 View

What is the standard method to perform insilico mutagenesis?

28 July 2015 9,677 4 View

What is the importance of the shape and size of the simulation box in a molecular dynamic simulation?

13 May 2015 2,676 4 View

How to extract DNA from Aspergillus spp. grown on solid medium?

Protocol for DNA extraction

11 July 2013 478 6 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View