For capillary electroosmostic flow rate characterization, which kind of solution can I get it from the common lab to be sucked into the capillary?

27 July 2018 1 393 Report

The solution should have several properties as inmiscible with water, adjustable viscosity and non-evaporated. Thanks for any suggestions.

Kadhim Kareem

Interested

Badges
Science topic

Similar topics
Engineering
Modeling

More Canwei Mao's questions See All

Why does inorganic phosphorus in labile pool cannot be transfered to stable pool directly?

In swat, epic, or any other models to calculate inorganic phosphorus cycle, why inorganic phosphorus in active pool can be transfered to stable pool, but inorganic phosphorus in labile pool can...

28 February 2024 1,530 4 View

Why is there a disagreement in partial charge calculation from Autodock and PDB2PQR?

I am docking a protein structure at different pHs. After obtaining the PDB structure, I protonate the protein at different pHs using pdb2pqr, download the structure, then use Autodock vina to dock...

07 February 2024 6,446 0 View

Can lentivectors be used for transient transfection in cell lines other than HEK?

Hi all, We have a lentiviral vector with a gene of interest that we would like to express. There is no requirement for stable cell line construction, so we will only be transfecting transiently....

29 November 2023 2,802 6 View

How do a splice correction of a spectrum with spliceCorrection in R language?

I have a spectrum CSV file and I have tried using the spliceCorrection function in R package "prospect" to fix it, but the result is not good. Can anyone please guide me on a method (Software) to...

24 September 2023 1,392 0 View

Why is 50% methanol used for protein A regeneration?

In most protocols, 50% methanol is used for protein A regeneration, followed by storage, usually in water/buffer/20% ethanol. In my experience, it is critical to apply a 50% methanol wash so the...

29 August 2023 2,511 3 View

Antibody expression - low amounts of heavy chain and full length monomers?

Hi all, I am trying to produce an antibody from a plasmid in Freestyle CHOS cells. The plasmid is a HC/furin/p2A/LC vector. The cells were transiently transfected during the exponential phase and...

12 July 2023 2,425 5 View

Time constant for mammalian cell electroporation?

For a project we needed to use a specific device (Bio-Rad Gene pulser) to electroporate mammalian cells. We set up the instrument with the following settings: Voltage = 1.9kV (we had to use this...

02 July 2023 7,753 3 View

Can FITC-labeled peptides be purified other than HPLC?

Hello all, I recently started to use peptides for cellular studies. Unfortunately, when I was designing the peptides I did not have a FITC tag to them (the peptide was synthesized by an external...

31 May 2023 1,689 3 View

No or low protein expression after transfection of a cloned gene- also low A260/230 plasmid ratio?

Hello, We have been trying to insert peptide tags (

07 March 2023 425 6 View

Error in Discovery studio, how to solve?

Hello all, I'm using Discovery studio 2019 to dock protein-protein, while "An error was encountered during execution of ViewResults.ds_pl.", then the dock failed. As it works quite well with the...

30 November 2022 829 4 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

How to add viscosity into a hyperelastic material such as Mooney-Rivlin rubber in LS-DYNA?

Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...

24 July 2024 5,908 0 View

Any relation between resin viscosity（mPa*s）and resin relative molecule weight？why the former is used in manufacture?

https://en.wikipedia.org/wiki/Viscosity

21 July 2024 3,089 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

How surfactant concentration affects the viscosity of nanofluids? Does viscosity increase with the increase of surfactant concentration?

In nanofluids, surfactants play a great role in stability. What is the impact of surfactant in viscosity in nanofluids? If surfactant concentration increases, then viscosity will increase/decrease...

24 June 2024 6,288 4 View

Which acrylic monomer combination is best to get tissue adhesion while making emulsion with adhesive properties?

I have tried combination of few monomers and resulting emulsion shows tack but tack is not enough to be measured by lap shear test machine, should I try new combinations or use some other method...

10 June 2024 5,305 3 View

Does anyone know where one can buy 8161 glass capillaries for making patch pipettes?

Warner used to sell 8161 glass, but Harvard Biosciences bought Warner and doesn’t appear to stock it anymore

04 June 2024 5,688 2 View

Effect of \nu variation for a turbulent pipe flow at a constat Reynolds number ???

I am trying to run a turbulent pipe flow simulation with turbulent Reynolds number of 600, for 15 seconds, the flow is pressure driven due to gravity enforced buoyancy force which gives kinematic...

20 May 2024 5,619 3 View

How to fix " turbulent viscosity limited to viscosity ratio of 1.000000e+05 in xxx cells" ?

Hi everyone, I try to do a simulation about heat transfer of supercritical hydrogen in a cooling channel. Properties of H2 is obtained from NIST and displayed by an UDF function. I used the k-w...

16 May 2024 4,076 2 View