Fiber Optic Sensor Labs

More Paul Macheso's questions See All

How to perform Cox proportional hazard analysis or Kaplan-meier survival analysis in SPSS?

At first please see the attachment. This experiment was performed for a period of 7 days (n=100). After 7 days, we found different level of survival rate (%) for each treatment. Now, I want to...

15 February 2021 9,145 2 View

For acid treated montmorillonite clays what will be the result of surface area?

The organo montmorillonite nanoclays modified with octadecylamine were used for the experiment. After acid treatment, the surface area will be increase. However, in my experiment, the surface area...

10 February 2021 1,581 3 View

How to identify when a gaussian program is about terminate normally?

Dear all, I am trying to optimize a bimetallic complex using # opt=tight b3lyp/lanl2dz scf=qc geom=connectivity. The program is running for around 5 days but the size of the .chk remains same...

05 February 2021 8,721 3 View

Can I use 500ng of DNA for restriction digestion?

The recommended amount of DNA for restriction digestion is 1ug in a 50ul rx I've got around 500-600ng of DNA in a total volume of 35ul. Would I get satisfactory results with this amount of DNA for...

31 January 2021 729 6 View

What is the effectiveness of online teaching during COVID-19?

Please share your experience on the effectiveness or challenges on online teaching during Covid-19 lock down. Share your experience about challenges, technology, online learning platform,...

26 January 2021 4,532 37 View

LC-MS metabolomics data after annotation some have their compound name but no KEGG id or with KEGG id but no pathway. How to interprete?

Recently I have generated LC-MS metabolomics data. After annotation, some have their compound name but either no KEGG id or KEGG id but no pathway. How to interpret those compounds? Additionally,...

18 January 2021 1,938 3 View

Has there been any scholarly research done in schools that addresses teaching from a global citizenship perspective to deal with global problems?

The current global pandemic, the climate crisis, the destruction of the oceans (with plastics, etc), and massive numbers of refugees are part of a set of serious global problems. It is clear...

13 January 2021 2,022 3 View

How to remove a citation from list of research articles?

I want to remove a duplicate citation

01 January 2021 3,983 3 View

No executable file generates while building geant4 example code, where is the problem?

Hello, I am a newbie in geant4. I'm learning it playing with example. Sometimes, when I go to simulate an example code, it doesn't create an executable file (the green one in my ubuntu terminal)....

26 December 2020 9,482 3 View

How to get structure and topology for glycosaminoglycan (GAG) of arbitrary length?

Hello all, I want to do glycosaminoglycan (GAG) simulation in Gromacs. Initial structure and CHARMM topology for short chains can be obtained from Charmm GUI glycan modeler. But I have to take...

23 December 2020 6,092 2 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

Staining methods for skeletal muscle fiber typing?

does anyone know the best method to differentiate and quantify rapid fatiguing and fatigue resistant muscle fibers? the old method form the 1980's uses ATP staining which is quite labor intense?

21 February 2021 6,483 3 View

What is difference between In-line transmission (%) and Total transmission (%) value of optically transparent Ceramics?

I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...

20 February 2021 9,405 6 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Alliance Tony-Mayeko

Hello we can discuss about Optical Fiber Sensors

Claudio Egalon

Hi Paul. I work with side illuminated optical fiber sensors, have the patents for this type of device and have come up with many demonstrations and labs based on this technology. What is exactly that you want to do with optical fiber sensors?