01 January 1970 1 8K Report

Hi! I need to etch silicon out from glass surface and at the moment I have no acces to KOH. Can I use other hydroxides such as NaOH or Ca(OH)2 and expect similar results?

More Martin Muller's questions See All
Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Similar questions and discussions
Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

In the presence of VERY high concentration (1000 ppm) of silicon, the adsorption isotherms of arsenic are showing anomalous trends, why so?

I conducted an adsorption experiment of arsenic on soil in the presence of different doses of silicon as competing ions to see the effect of silicon on arsenic adsorption and desorption. I took 5...

03 August 2024 6,500 3 View

Is there an explanation of why a negative photoresist take-off after contact with ferric chloride (like in the pictures) ?

Deep etching Negative photoresist Acrylate polymer Chemical etching Ferric chloride Crosslinking Resolution

11 July 2024 2,476 4 View

NH3/NF3/H2 Remote plasma Oxi/nit selective etching mechanism help ??

Hello, I am an Etch Engineer. I am performing etching with high T_ox/Nit selectivity using remote plasma. Etching plasma is formed using only NH3/NF3/H2. 1. I wonder if it would be advantageous...

11 July 2024 8,115 2 View

Does the potentiostat have to be in a fume hood when polymerising the PANI?

I will polymerise Aniline on ITO glass WE, using 1M of H2SO4 and a potentiostat. However, I am not sure if I have to do the electrochemical polymerisation inside a hood. Is it necessary? Is the...

10 July 2024 2,937 3 View

Where to source glass rings compatible with cell culture?

Hi all, I am looking glass cilinders that have an open flat bottom and top. Preferably with the inner diameter in the range of 2 cm. It's similar to the ones found on multi-electrode arrays for...

06 July 2024 5,846 1 View

What is alternative for PMMA?

If we want to introduce a material similar to polymethyl methacrylate "with the characteristics mentioned in the next paragraph" that can be added to a precursor and create a composite, which...

03 July 2024 2,371 1 View

Why PDMS is not hardening ?

I use PDMS to build a microfluidic system, but it is not hardening at all, although I use TEOS as a cross-linker and also ATPES in a ratio of 1:10, and it's been 3 days at 80 degrees of 3 ml cast...

01 July 2024 604 3 View

How to solve this error while I simulate gidl using tcad ?

There is an error message "interface silicon/oxide not found in grid xxx.tdr file"

26 June 2024 5,551 0 View

To generate hydroxyl radicals the photcatalyst need to be in conatct with water or air pollutant?

Is direct contact of polllutant and catalyst needed? or indirect contact just like photocatalyst wrapped inside glass can also create hydroxyl radicals and elimnate pollutants near to its wrapped...

23 June 2024 3,249 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close