How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

How does GROMACS calculate the average structure of proteins?

I want to get a average structure from a pdb file containing multiple models. I used the command below: gmx cluster -f input.pdb -s topol.tpr -cutoff 20 -method gromos -av GROMACS...

25 February 2021 6,314 1 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

R/Python package for time-intensity or progressive profiling in sensory evaluation?

Hi I've been looking for a stat package for my sensory evaluation data (progressive profiled which is a multi-timepoint version of descriptive analysis). Is there any available one to...

08 February 2021 9,170 3 View

How can I make sure the simulation results of the water droplet impacting on the wall using the FLUENT agree with the experimental results?

Dear researchers, I am modeling the process of the water droplet impacting on the wall with a constant contact angle. The specific calculation parameters are as follows: The droplet diameter is...

24 January 2021 1,020 5 View

Mysterious line across SDS gel?

Does anyone have the similar issue? A line across the denature SDS gel shows up after staining with Coomassie blue and there are many lines in every lane if you take a closer look. This gel had 15...

07 January 2021 5,610 4 View

How can I calculate packing density of particles by fomulas or softwares?

I have all data of particles, such as size distribution, or numbers. Is there any way that I can calculate the packing density of these particles? Assume that all particles are circular.

05 January 2021 4,272 2 View

After cellulose is regenerated in water, a cellulose hydrogel is formed. I want to know if there is crystallinity inside the the hydrogel?

After cellulose is dissolved and regenerated in water, a regenerated cellulose hydrogel is formed. I want to know if there is crystallinity inside the hydrogel, or it will not crystallize until it...

04 January 2021 7,466 4 View

How can I fix the density of system in coarsed grain simulation?

In the process of obtaining the nonbond potential of the Coarse-grained(CG) model, I need to simulate the CG model mapped from the conformation of all atom(AA). AA simulation process is...

02 January 2021 3,643 1 View

How to export Mass and Stiffness matrices using Ansys Workbench?

Hello, I am trying to export Mass and Stiffness matrices using Ansys Workbench via Modal analysis modular, with APDL commands inserted. However, there is no .matrix file generated. Could anyone...

17 December 2020 1,196 5 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View