Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

17 January 2021 5,522 3 View

Potassium formate/water or potassium formate+LiBr/Water are not available in the commercial sector for absorption refrigeration systems?

Although there are already studies in the literature but not much , the use of potassium formate/water or potassium formate+LiBr/Water are not available in the commercial sector for absorption...

16 November 2020 2,917 2 View

Fuel and product exergy rates ?

How to write the fuel and product exergy balances in the cascade heat exchanger in the cascade refrigeration system?

22 September 2020 1,954 4 View

Nanoparticle for absorbtion refrigeration system ?

How can concentration in terms of rich and poor be affected by adding nanoparticles to LiBr-Water?

23 March 2020 6,718 7 View

1)A question of quadruple integral ??

I cannot solve by maple or mathematica software. Can you help me

16 December 2018 696 2 View

Potassium formate/Water

Although there are already studies in the literature but not much , the use of potassium formate/water or potassium formate+LiBr/Water are not available in the commercial sector for absorption...

01 January 1970 3,749 3 View

Who can help me model the absorption cooling system in Aspen Plus?

I am trying to model a single-effect absorption refrigeration system using LiBr/H2O in Aspen Plus. Who can help me model the absorption cooling system? Please send a private message.

01 January 1970 6,733 6 View

Calculation of performance parameters of absorbtion refrigeration system with nanofluid?

Hello, My reseacrh area is absorbtion refrigeration system with nanofluid. I know how can I calculate the performance parameters of NH3-WATER and LiBr-WATER as a base fluid. But the thing is, how...

01 January 1970 7,246 3 View

calculator block of mass flow rate in aspen plus

why I need to enter the mass flow rate in stream 1 in aspen plus ? For example, I entered the mass flow rate as 1 kg / sec. I want to change it according to the cooling load of the evaporator but...

01 January 1970 8,047 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View