Electron transfer dependence on density of nanowires?

Babu Balraj @Babu-Balraj

18 May 2020 0 3K Report

Dear Scholars,

How does the electron transfer increases with the increase in the density of nanorods?

Badges
Science topic

Similar topics
Physical Sciences
Energy

More Babu Balraj's questions See All

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to get nanocomposite of PEEK with Zirconia ?

Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...

13 December 2020 4,329 5 View

How can I get eggs of an univoltine casebearer moth for a threshold study?

I am planning to conduct a cage study to determine a critical density of an univoltine casebearer moth in red clover seed crop. This requires to release first instar larvae in the cages with the...

02 November 2020 6,577 3 View

Can anyone suggest me free and fast scopus publication with highly acceptance rate?

Q3,Q4 will be okay. I need scopus publication without APC and fast published. The paper is from Computer science discipline.

19 October 2020 4,255 4 View

Bio-intensive cropping systems can reduce the environmental foot print?

The adoption of bio-intensive cropping systems has the potential to reduce environmental footprints without compromising the economic gain per unit of resources.

12 October 2020 2,625 7 View

Application of Polyhalite changes the nutrients chemistry in soil?

Polyhalite is a multi-nutrient source, its application assume to be changes the soil biology and nutrients chemistry on long term basis

12 October 2020 6,685 3 View

How to recycle Sodium Iodide?

Hi, I am using sodium iodide to separate density carbon fractions of my samples. I want to recyle it for further uses. While searching I only get the process to recycle sodium polytungstate (at...

20 September 2020 9,556 2 View

Purpose of keeping the rocket nozzle assembly inverted, for Actuator-In-Loop simulations ?

For Actuator-In-Loop simulations, why are the rocket engine nozzles along with the thrust vector control assembly (including the actuators) kept inverted on a platform like in the attached image...

14 August 2020 8,652 2 View

How to add attenuation model and spectral ordinate in R-CRISIS?

Hi Everyone I am using R-CRISIS for seismic hazard map creation. I know how to use the given attenuation model in R-CRISIS but I want to use an attenuation model from a published article. How to...

23 July 2020 5,265 1 View

Is there any python module is available for statistical seismology?

Could you suggest any python module that is made for dealing with statistical seismology?

29 May 2020 9,068 6 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View