What is the difference between L1 and L2 regularization in machine learning?

L1 and L2 regularization

28 February 2021 4,187 3 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

Which power-to-heat (P2H) devices do you think are likely to play the most crucial role in the European energy transition?

Power-to-heat (P2H) shows how we can use renewables for heating. Power-to-heat technologies have been on the market for quite some time now, with heat pumps being the most important. However, they...

10 February 2021 9,250 2 View

Why we use feature normalization before using the Gaussian kernel in SVM?

Support vector machine

09 February 2021 6,405 3 View

How is KNN different from k-means clustering?

machine learning

09 February 2021 8,757 9 View

What is bagging and boosting in Machine Learning?

machine learning

09 February 2021 5,156 3 View

Do the introduced salts (NaOH/ HCl) influence the spectroscopic shifts of the fluorescence excitation-emission matrix?

During the resin (XAD-8) fractionation of wastewater salts (NaOH or HaCl) are used for acid or base elutions/pH adjustments. Since the amount of introduced salt is minimal, so is it required to...

08 February 2021 9,489 2 View

Do you think it is feasible to have a 100% Renewable Energy-based Electricity System in Bangladesh in the distant future?

In Bangladesh, the proved reserved of natural gas 34 TCF which will lead the country next 20 years and currently 82% natural gas consumed in the power sector for power production. Whereas only 3%...

01 February 2021 251 12 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View