What is the general cyclic energy degradation factor for plain concrete at material level in stress strain curve?

Plain Concrete subjected to cyclic loading get reduction in its stiffness and strength with the every cycle of loading. What is ratio of energy enclosed in one hysteresis loop to adjacent...

10 February 2021 1,051 1 View

The Akaike information criterion of the random forest model ?

Please, how to calculate the number of model parameters of the random forest model to determine the Akaike Information Criterion (AIC) using this following expression: AIC = n * log(MSE) + 2 *...

27 January 2021 816 6 View

Suggest me some satellite image datasets used for crop yield estimation?

I have my synopsis presentation and i have to provide details about 2-3 datasets that I can use in my research. Topic is crops Yield estimation using satellite images. suggest me what I can write?...

13 January 2021 1,675 3 View

What is the reason of suddenly increasing the concentration while evaluating the photocatalytic performance by RhB dye degradation?

I am doing a photocatalytic performance evaluation by RhB dye degradation. I am facing a problem which is: After achieving the absorption -desorption equilibrium, I checked the concentration and...

04 December 2020 3,922 20 View

Edu assay by spectrophotometry means?

Dear all, Have any one performed edu assay by spectrophotometric means ? I'm looking for a kit for that purpose. I have Chinese kit for this purpose, I followed their protocol but the result is...

24 November 2020 1,766 3 View

Either SEM analysis are enough to justify the morphology and micro structure of activated carbons? or I should go for TEM analysis as well?

While I was discussing my nitrogen adsorption isotherms in the context of micropore, mesopores, total pore volume for activated carbon samples prepared from waste materials, I received a review...

13 November 2020 1,971 3 View

How can we measure dissimilarities between two images layout? Like alignment of button, text box, text overlapping?

I want to extract dissimilarity information of two images layout. Wanna check text, button, and text box alignment, text overlapping, and more other layouts difference. how we do that? any tool,...

25 October 2020 7,190 7 View

Any suggestions of bioinformatic tools to identify/predict the effect of mutations observed on the function of proteins?

04 October 2020 1,552 4 View

How to Determine LD50 of a test compound by Lorke's Method if your mice (mus musculus) dies at the lowest concetration i.e. 10mg/kg?

I have used Lorke's method of determining LD50 of my test drug. The lowest dose according to this method is 10mg/kg and my mice died at this dose within the 30 minutes of IP injection. Does that...

22 September 2020 9,959 3 View

How to do MTT for non-confluent cells?

Hi everyone, I'm doing MTT assay to test the cytotoxicity of 4 candidates on the BT-474 breast cancer cell line which rarely becomes confluent. started with 3K/well, 5K/well, 6.5K/well left the...

12 September 2020 3,034 8 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View