Effect of Severe Discontinuity Iteration and Equilibrium Iteration on results in Abaqus ?

More Sachin Wakchaure's questions See All

How to make graphene oxide film on substrate for electrochemical performance?

I am trying to deposit graphene oxide film on steel electrode via drop casting (Electrochemical synthesis of layer-by-layer reduced graphene... ) and dry it in oven at 60 C. when i put this into...

04 December 2020 820 2 View

If anyone can suggest or review manuscript having keywords Riparian zone, River, Species richness, Species evenness, Ornithofauna?

Greetings I am Sachin Kumar, pursuing my Ph.D. in Ornithology, from PAU, Ludhiana. I am working on avian diversity along the River Beas. I had submitted a manuscript to a journal having keywords...

10 November 2020 7,194 6 View

Can anyone provide me .pdb file for Spike protein of SARS Cov-2, ACE2 complex and TMPRSS2?

Dear Research Colleagues, I am looking for the .pdb file for Spike protein of SARS Cov-2, ACE2 complex and TMPRSS2. I have to use them for Molecular Docking analysis of synthetic organic compounds...

08 September 2020 8,788 3 View

Can i use Ag/AgCl reference electrode to electrodeposite silver?

I'm trying to electrodeposit silver nanoparticle from aqueous solution of AgNO3 via three electrode configuration. When i dip three electrode in aqueous AgNO3 solution, a whitish fluid coming out...

22 August 2020 6,837 7 View

Can i use Graphite flakes having 325 mesh particle size instead of Carbon Black or acetylene to make slurry for electrochemical performance ?

Can i use Graphite flakes having 325 mesh particle size as conductive agent instead of acetylene black or carbon black to make slurry for super capacitor electrode ?

27 July 2020 1,176 1 View

Why bubbles appear on film during Galvaostatic charging discharging?

I electrodeposited GO/PANI directly on electrode and dried at room temperature, then used it for Galvanostatic charge discharge via three electrode configuration in 1 M H2SO4. During charging...

20 July 2020 5,988 8 View

Is it necessary to do Open circuit potential before CV, Galvanostatic charge discharge and EIS for Supercapacitor electrode?

for electrochemical performance of supercapacitor electrode i am doing CV, Galvanostatic charge discharge and Potentiostatic EIS via three electrode configuration. is it necessary to do open...

19 June 2020 2,026 7 View

Does metal to metal joining by FSW really occur so as to withstand loads in abaqus?

I am curious to know if metal bonding by welding (FSW) can really be simulated in Abaqus or not. I have read many papers wherein people simulate the FSW process only and study the temperature and...

15 June 2020 6,471 1 View

Which is correct formula to calculate gravimetric specific capacitance from Galvanostatic charge discharge method?

I have to calculate specific capacitance (F/g) from galvanostatic charge discharge. in electrochemical test, one is working electrode, platinum sheet as counter electrode and Ag/AgCl as reference...

07 June 2020 5,213 3 View

How to develop 3D setup for abrasive jet machining in ansys fluent ?

hello everyone....... I am trying to develop 3D setup of abrasive jet machining (AJM) which consist of nozzle from which stream of air+abrasive (two phase flow) strike the workpiece and erosion...

30 May 2020 2,136 8 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View