Effect of Ice loads on Semi-submersible?

17 November 2019 0 10K Report

Hello friends,

I would like to know that, can we find the effect of ice loads on the response of Semi-submersible using Ansys Aqwa?

Using the available Ice-force time history, developed for continuous crushing and giving it as "structure force" as the input in Ansys Aqwa. Does it really work?

If yes, I can go ahead.

If no, please suggest me how to carry out the response analysis of Semi-submersible under wave, current and ice loads.

Sincerely waiting for your suggestions.

Badges
Science topic

Similar topics
Physical Sciences
Waves

More Syed Azeem Uddin's questions See All

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

Why is my CFD problem (mini heat sink rectangular channel) not converging while having good quality mesh?

My CFD problem is having two interconnected rectangular channel, which is known as mini heat sink. I have already performed parallel flow inside of an interconnected mini heat sink. However, I...

19 February 2021 3,209 3 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

How to get actual or true SoC while predicting SoC for Batteries using Data Driven Approaches?

I have seen it in multiple research articles that authors use certain approaches to predict electric vehicle battery's state of charge(SoC) and then they compare it with battery's true SoC. So I...

11 February 2021 9,070 3 View

Hi, does any one know how to redisperse the ppt of gold NPs formed after conjugation with the drug molecule?

gold surface is already conjugated with the PEG-2000 linker but still when I tried to conjugate it with the drug, It gets precipitated

25 January 2021 2,602 1 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Could anyone tell me what is the range of submillimeter wave?

There is confusion regarding the submillimeter-wave range. Many papers specify its range from 300GHz but some also consider its range from 100GHz. If I design an antenna on 122ghz what would I...

01 March 2021 516 7 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Could you please suggest to me research in which a relation between the shear wave velocity and the degree of saturation for stone was discussed?

Hi all, I am looking for a graph or a relation that relates the degree of saturation and the shear wave velocity for the marlstone. Looking forward to your suggestions Best Regards

24 February 2021 9,690 1 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

How to include additional force field in GROMACS?

I have a cellulose model system that is best described by the GLYCAM06 force field according to the literature. However, the set of force fields included in the GROMACS package doesn't include the...

20 February 2021 3,309 3 View

Absorption behaviour of anechoic model?

I have modelled a unit-cell of an anechoic structure using ANSYS. The layer is silicone and has been assigned as an acoustics physics region, with an air cavity inside (the air has been modelled...

18 February 2021 4,119 1 View