Dropwise vs direct addition of chitosan folate?

More Ghazal S. Panahi's questions See All

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

Do you have any experience with transfection of EBV immortalized B cells with Lipofectamine?

I know that efficiency of transfection for primary B cells is very low with Lipofectamine. But I did not try that for EBV immortalized B cells. Do you have any experience with transfection of EBV...

05 February 2021 4,159 1 View

What solvent can I used for Paal Knorr reaction between 6-amino hexanoic acid and 2.5 hexanedione?

I am try to make the Paal Knorr reaction between 2.5 hexnedione and 6-amino hexanoic acid, my problem is type of solvent to use, because 6-hexaminohexanoic acid is soluble in water but I am not...

02 March 2021 4,443 2 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View

I want to performe MALDI-TOF MS for bacterial identification, I would appreciate it if anyone can tell me the matrix solution preparation protocol ?

based on what I've studied on multiple papers, for peptide and protein identification Alpha-cyano-4-hydroxycinnamic acid (CHCA) is an appropriate matrix to use, I also know that the CHCA powder...

26 February 2021 6,799 3 View

Can I use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography?

Hi! I would want to know if I can use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography. This column has a polyethylene glycol phase, but I can't find the manual to check...

22 February 2021 730 2 View

Can you perform the Murexide test on samples fixed in Formalin?

I have a fixed sample and would like to use the murexide reaction to test for uric acid composition. I no longer have fresh samples

22 February 2021 1,328 1 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Protocol for membrane extraction E. coli?

Hello! I am interested in determining whether a poly-unsaturated fatty acid I have engineered E. coli to produce is being incorporated into the membrane of the cells or if it is simply a free...

21 February 2021 7,447 2 View

What is the stability of 2 3-dihydroxyquinoxaline in acidic water?

I'm developing a UHPLC assay, and the fluorescent product is 2,3-dihydroxyquinoxaline. The reaction to produce this requires hydrochloric acid (about 1.2 M). Will storage in this acidic...

20 February 2021 5,820 4 View

Chinaza Godswill Awuchi

Kindly check https://www.sciencedirect.com/science/article/pii/S2405844017329729

Also check https://www.sciencedirect.com/science/article/pii/S1818087618308420

Ejaj K Pathan

Ghazal S. Panahi The addition of chitosan should be slow, add 1/10th (or less) of the total amount at a time, allow it to mix properly and then add on in the same way.