Does some body having Idea of improving Granulation Index in Iron Sinter Making by altering surface tension of water, Using surfactant ?

More Mahesh Kumar Sharma's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Non -oxidizing metal binders?

I'm trying to sinter some Nb parts and I'm trying to find a binder which does not produce oxidative compounds when it decomposes.

25 July 2024 9,823 3 View

Differences between Surface Tension and Interfacial Tension in Liquid-Gas Phases?

Hi everyone, I have a question regarding surface and interfacial tension. Although I understand that these tensions are studied for different purposes, can they be considered equivalent in the...

18 July 2024 382 5 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How to Dedust Activated Carbon Granules?

Dear all, We are producing activated carbon from hazelnut shells but have an issue about the dust of the a.c. granules also known as the dust film on granules. Linear vibrating seives doesn't do...

11 July 2024 9,782 2 View

How to change the author?

Hello! Research of factors affecting thickness of the covering obtained by electro contact sintering of composite materials. This is my article, not Varvara. How to change the author? Incorrect...

09 July 2024 3,829 0 View

Transparency oin-in-water emulsion but larger size particle ?

Dear Colleagues, I am currently formulating oil in glycerin/water nanoemulsionn of Thymol and Eugenol, using cationic surfactant. After phase diagram, I got trouble that the clear and...

03 July 2024 4,200 2 View

Vadim Verlotski

Yes, such surface-active additives as polyvinyl alcohol, polyvinyl acetate, methyl cellulose and a couple of other water-soluble polymers dramatically improve the granulation (agglomeration) of metallic powder in water-based suspensions.

Mahesh Kumar Sharma

Thank you for the information.