What happens to the same phenomenon when it's a UD or Off-axis or multidirectional laminate?
Extraction of three different phases of metapelites, mostly phyllites as the Carbonate phase, Fe-Mn Phase, and Silicate phase has been obtained. After doing ICPMS, different results have evolved....
11 February 2021 5,198 10 View
Hello, I am trying to observe pressure drop oscillations during boiling flows in Ansys Fluent. To do that I am trying to get more accustomed to modeling flow boiling in the software. So far I...
01 February 2021 6,446 2 View
I am in need of the help of anyone who is working on measurement of globalization? Please inform me at the earliest.
23 January 2021 1,259 1 View
can it be diagnosied by the same tool or different tool
04 January 2021 2,964 2 View
The general public must be made aware of the mode of transmission, presenting symptoms and the measures that can be undertaken to prevent the spread of infection. Few options- Media, Webinars...
03 January 2021 3,538 13 View
Hi All, Are there any python modules available for old HP-Agilent spectrum analyzers around? I know PyMeasure has a library of some commonly used and new electronics but I am looking for old ones...
21 December 2020 3,460 3 View
Please tell me about the rate (in SCCM unit) of the flow of gases and pressure inside the tube.
12 October 2020 8,315 3 View
I want to scan my experimental mice bone samples using micro CT instrument. I have gone through several research articles for ideal scanning parameters like voltage, current, filter etc. but these...
11 October 2020 8,069 2 View
Hi, We have a small test run for a set of RNA samples with 3 fluorophores, FAM, HEX, and Cy5. FAM and HEX are for test samples while Cy5 is with internal control. Surprisingly, for some of our...
03 September 2020 7,713 3 View
How to calculate the defect charge formation energy for a metallic system (bulk/surface) using DFT? The defect formation energy is calculated by the following formula E_formation (D,q) = E (D,q)...
23 August 2020 6,047 4 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...
01 March 2021 9,911 3 View
for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...
26 February 2021 3,668 1 View
25 February 2021 6,760 1 View
I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...
24 February 2021 8,105 3 View
I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...
24 February 2021 8,678 2 View
I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...
21 February 2021 8,694 4 View
Dear all, I hope everyone is safe and healthy I do have a question please. Where can I find a drop-weight impact testing machine to test fiber reinforced polymer composite plates (CFRP and GFRP)...
17 February 2021 3,820 3 View
Hi everyone, I am conducting a non-linear multi-layer pavement structure analysis which is a stress-dependent. So far, I am able to define the nonlinearity for one soil layer for its resilient...
11 February 2021 9,607 3 View
The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...
11 February 2021 952 6 View