Does anyone know the experimental setup of gas sensor for impedance analysis using potentiostat/galvanostate?

More Sureshkumar Sundaravel's questions See All

Can anyone explain how we can measure the H2S gas concentration in ppm level?

Suppose we have a cylinder containing 1000 ppm H2S in N2, how can we measure the H2S gas in ppm level? It goes to the gas testing chamber at a constant flow rate.

09 October 2014 1,555 7 View

Is Yttria stabilized Zirconia a non conducting material?

Is Yttria stabilized Zirconia conduct electricity?

09 October 2014 7,908 3 View

Is possible to deposit ZrO2 on SS316L by EPD?

Need related paper

11 December 2013 9,379 6 View

How can we calculate quantum yield in a cary eclipse fluorescence spectrophotometer?

From this we can take excitation, emission spectra.

03 April 2013 2,055 6 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

What is the best conditions for formation Magnetite ore deposits?

I want to know more about Magnetite deposits.

06 August 2024 1,066 0 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Muhammad Awais Khan

http://www.bio-logic.info/potentiostat-electrochemistry-ec-lab/instruments/

http://nuvant.com/products/potentiostat_galvanostat/?gclid=CPTEgPmwxL0CFfMQtAod6gIA5w

Sungjun Park

It depends on the circumstance of materials in experiment.

please let me know the object(goal) of your experiment.