Does anyone know how to import GFS forecasts into Delft-FEWS?

Mawuli Dzakpasu @Mawuli-Dzakpasu

19 April 2016 1 884 Report

Samyadeep Ghosh

The following link might help:

https://publicwiki.deltares.nl/display/FEWSDOC/Importing+USA+weather+forecast+into+Delft-Fews

Badges
Science topic

More Mawuli Dzakpasu's questions See All

Please does anyone have a lead on this article by Manus UC, 1998 "African Christologies: the centre-piece of African Christian theology" ?

This article is relevant to my PhD thesis. I am researching on the topic "African christology and the fight against corruption in Ghana".

16 July 2021 6,091 5 View

How do I adapt mosquitoes to membrane feeding?

As part of my thesis I need to do membrane feeding in order to determine the infectiousness of gametocytes

16 January 2019 4,000 26 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How is energy cycled through the Earth's climate system and how do matter cycle and energy flow through the rock cycle?

08 August 2024 8,162 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View