Does anyone know about the pigment stability and appearance of crossover area on epoxy floor coatings?

More Bahareh Razavi's questions See All

How can I improve the quality of lamb milk replacer for machine feeding?

Hello everyone, I am researching ways to enhance the quality of lamb milk replacer for machine feeding. I would appreciate any insights or recommendations on the following: Manual vs. Machine...

06 August 2024 6,227 2 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

How to apply virtual site for a polymer?

Dear All, I have a PDB structure for a complex and large polymer. I need to perform MD simulations using the OPLS-AA force field. I obtained the force field parameters from LigParGen and created...

11 July 2024 5,109 0 View

How to accelerate the growth of dermatophytes in culture medium?

Hello. I have cultivated the species of dermatophytes in the special culture medium of SCC. Unfortunately, the rate of species growth is very slow. Does anyone have any experience in this field,...

26 May 2024 4,552 3 View

The reletive between cognitive function and physical activity(In the ages of physical and mental development)?

In the study of the statistical population of women, was there a relationship between cognitive functions and physical activities that could be focused on more?

20 May 2024 6,003 0 View

Does any one know any program used instead of ProDrg?

Hello every one. I want to simulate a drug through membrane and i need to gain structure and topology file of the drug molecule . i used to do this by using Prodrg under-web program but...

15 May 2024 5,439 0 View

How to Precipitate Hydrophobic polymer?

I have 2 2 2-trifluoroethyl methacrylate polymer solution and I want to separate polymer from solvent , I used methanol but my polymer solution in methanol seemed cloudy . How can I precipitate...

10 May 2024 6,823 4 View

How to quantify the color on the surface?

I have anti-graffiti surface samples sprayed with graffiti spray. I am going to measure intensity changes in color of surface. How can I quantify them?

24 April 2024 8,574 5 View

How to calculate the UV-Vis spectra using implicit solvents?

Dear all, I need to calculate the UV-Vis spectra with an explicit solvent. For that, I think I need to conduct some MD simulations, extract the structure from the MD results, and then perform...

15 April 2024 4,724 0 View

How can I obtain friction velocity(u∗) and scaling humidity (q∗) values in order to calculate transfer coefficient for latent heat(Cez)?

I want to calculate the latent heat flux(Qe) and for that I need the Cez value.

03 April 2024 6,844 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

A positively charged and 10x his-tagged protein that doesn't bind to any chromatographic resin?

Hello everyone, I am currently working on a protein that is 10x his-tagged and positively charged (predicted pI=10.16). But when I tried to use Ni-NTA column to purify the protein, it's not...

24 July 2024 7,293 4 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

Prevent sedimentation and maintain the suspension of powder particles in the resin ?

Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...

23 July 2024 1,672 0 View

Any relation between resin viscosity（mPa*s）and resin relative molecule weight？why the former is used in manufacture?

https://en.wikipedia.org/wiki/Viscosity

21 July 2024 3,089 4 View

Is it possible to conjugate an NHS ester to the N-terminus of a peptide ON RESIN?

So i have a few peptides (synthesized by SPPS and not cleaved from resin) and I want to add a maleimide label. We have NHS-PEG-Maleimide and from literature it is evident that the free amine group...

18 July 2024 4,075 3 View

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

Recommendations for his-tag magnetic beads / resins?

Good day everyone, Trying to perform protein purification for the first time, gotta buy the whole equipment/reagents. Protein of interest 48 kDa (Antithrombin), expressed from his-tagged plasmid...

16 July 2024 3,692 6 View

Asked a separate ways?

Dear all, I have a question regarding ways to separate ammonium nitrate and phosphorus pentoxide？

12 July 2024 3,164 2 View

Does the potentiostat have to be in a fume hood when polymerising the PANI?

I will polymerise Aniline on ITO glass WE, using 1M of H2SO4 and a potentiostat. However, I am not sure if I have to do the electrochemical polymerisation inside a hood. Is it necessary? Is the...

10 July 2024 2,937 3 View

Neda Kayhan

Hi.I worked on this paint.pigment stability related on epoxy resin that you used.

Bahareh Razavi

Hi Neda. Thank you for your answer. I used Bisphenol A epoxy resin. Which parameter do you mean on epoxy resin?

epoxy resin cured with amine hardner

I know about that but still I have problem with the pigment stability and appearance of crossover area on epoxy floor coatings.

You must used dispersion additives for dispersing and wetting of pigments.epoxy resin that you used must be low viscosity.maybe your pigments are not suitable for this paint.you dont say your problem clear.

!!!