Does anyone have a short, printable guide of the Autodesk CFD simulation?

More Piotr Nikończuk's questions See All

How to import and convert a .ply file to MATLAB?

I'm going to import the *.ply file to MATLAB to plot the image using the mesh instruction and use the matrix for calculation.

11 December 2013 7,351 3 View

Heat transfer measurement by infrared camera - any suggestions?

I'm going to measure the thermal conductivity with an infrared camera. I put the sample on the heating element. The remaining part of the heater is thermally insulated. Thermal image of the sample...

09 October 2013 3,039 8 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Florian Carle

Piotr, I couldn't find any short help guide for you to print, but I have found out that you can add a help add-on to your software (available here http://usa.autodesk.com/adsk/servlet/ps/dl/item?siteID=123112&id=21208244&linkID=18154757) as well as some API documentation. You can also find a lot of tutorial to help you learn how to use Autodesk CFD (here: http://wikihelp.autodesk.com/Simulation_CFD/enu/2014/Help/0083-Tutorial83)

I hope it will help you and good luck with your simulation model!

Piotr Nikończuk

Thank you Florian,

WikiHelp is useful but is not printable in full

anyway I am working on a simulation :)

Awesome! I hope you'll learn all you need for your research