Does anyone have a SHIMADZHU UV-1601 PC, USB virtual COM port (RS232 to USB)?

17 April 2023 1 3K Report

Hello.

I have a SHIMADZHU UV-1601PC spectrophotometer. I need to use UV probe software on my PC that it doesn't have a 232 port (COM), So, i need to use an USB virtual COM port (RS232 to USB).

Is there any one use it because it doesn't work with me . Could you share?

Qudrat Ullah Khan

https://youtu.be/7zOB0sP-kBo

https://youtu.be/lEx3pweaTz8

Badges
Science topic

Similar topics
Filing

More Rachid Lamari's questions See All

How to carrying out strain modal analysis using AnsysWorkbench?

The displacement mode shapes are determined by running the modal analysis on AnsysWorkbench. How we can have the strain mode shape and the modal strain energy using ansysWorkbench. Example:...

07 December 2020 7,845 3 View

How to resume a Gate (geant4) simulation after a crash or power failure?

Very long simulations may be subject to computer failure for many reasons. Is there a command in Gate to save (or dump) the state of a simulation and be able to resume it later?

04 October 2020 8,133 2 View

How to apply a different material on a group elements of global model?

how to apply a different material on a group elements of global model? i have a wind turbine blade model (complex model) . I want to model a defect on the blade by reduction of young modulus of a...

17 August 2020 1,377 3 View

What do you think about the expulsion of 21 teachers in Jordan university ?

Hello What do you think about the expulsion of 21 teachers in Jordan university because they did not publish any research in the last five years ? Is this an efficacy solution , can we apply it...

22 July 2020 914 34 View

How to draw light lines on dispersion diagram extracted from CST- eigenmode solver?

Hello, I have a non symmetric unit cell with a period over y axis of 48mm. I know that f= c. teta / 2*pi*p having teta in radians. However, I am getting a very weird light lines.

25 May 2020 5,889 3 View

What is the best method for non-linear resolution of the solar/PV cells characteristic ?

Evolutionary Algorithms, namely Genetic Algorithm (GA), Particle Swarms Optimization (PSO) and Differential Evolution (DE) are used to solve optimization problems. As in photovoltaics (PV), the...

05 May 2020 8,708 8 View

How to find the displacement of each of the model nodes as well as its position on the model using AnsysWorkbench, after a modal analysis?

In several studies of the analysis of the defect effect on the dynamic characteristics of the structure, the defect is modeled by reduction of the modulus of young. I want to perform this method...

20 April 2020 4,644 3 View

What is the relationship between Glass Transion Temperature (Tg) and testing rate?

In other terms the influencing of testing rate on Tg. Excuse me for my beginning english

14 January 2020 706 3 View

Can anyone help me in classification of EEG signal?

Can anyone help me in classification of EMG signal? I had EEG signal and want to classify into four different action by using matlab classification learner app. I had xdata with time and ydata...

16 September 2019 3,698 2 View

A recurrent question about interaction value in linear mixed model. How to get it with a t value?

I apologize for asking again the same question, but il really don't have a satisfactory response. In different article, I find more and more (focused on eye movement in reading) that interaction...

05 June 2019 3,223 8 View

How can I apply position restraint to a bilayer during Umbrella sampling for PMF calculations?

Hi all, I have a couple of questions for PMF calculations in Gromacs. I placed a nanoparticle (NP) in the water region approximately 1nm away from the membrane and by using Gromacs pull code, I...

21 April 2020 3,827 4 View

How to measure traffic flow in VISSIM 10 with COM interface?

Hi everyone, I am doing traffic modeling with VISSIM 10 and the COM interface. I am writing some Python scripts to run VISSIM simulations, implement some scenarios and controls, and collect data....

26 February 2020 5,935 1 View

How to set spring constant for umbrella sampling in GROMACS?

Hello everyone, I'm new to gromacs and also new to umbrella sampling, so I'm following Justin's tutorial http://www.mdtutorials.com/gmx/umbrella/index.html ; On the umbrella sampling stage, I'm...

20 February 2020 1,781 3 View

How to measure traffic flow in VISSIM 10 with COM interface?

Hi everyone, I am doing traffic modeling with VISSIM 10 and the COM interface. I am writing some Python scripts to run VISSIM simulations, implement some scenarios and controls, and collect data....

01 February 2020 6,857 1 View

How to set spring constant for umbrella sampling in GROMACS?

Hello everyone, I'm new to gromacs and also new to umbrella sampling, so I'm following Justin's tutorial http://www.mdtutorials.com/gmx/umbrella/index.html ; On the umbrella sampling stage, I'm...

01 February 2020 3,807 3 View

How can I measure the cluster size between center of mass?

I need to measure the aggregation of a type of molecule. The aggregation will happen if the COM of molecules becomes less than 0.85 nm. I think I should use g_clustsize but it normally calculates...

11 December 2019 2,207 4 View

Is the any way to use clustsize keyword based on the center of mass in gromacs? or a specific atom?

I want to measure the number of monomers, dimer, ... between the same molecule in my simulation box. I am using the following code: gmx clustsize -f mdrunps.xtc -s mdrun.tpr -n index.ndx -tu ps -b...

11 December 2019 4,515 4 View

I am simulating a protein in Gromacs in implicit solvent. But I am getting few errors. I tried some changes but nothing happened. Can you help?

This is the input file for equilibration. title = NVT Equilibration ; Run parameters integrator = sd ; leap-frog integrator nsteps = 250000 ; 2 * 50000 = 100...

21 November 2019 7,204 7 View

I am simulating a protein in Gromacs in implicit solvent. But I am getting few errors. I tried some changes but nothing happened. Can you help?

This is the input file for equilibration. title = NVT Equilibration ; Run parameters integrator = sd ; leap-frog integrator nsteps = 250000 ; 2 * 50000 = 100...

10 November 2019 1,207 7 View

I have fixed COM of clay but is it necessary to dfix COM of simulation box during simulation?

Dear all, I am working on clay in water box. I have fixed the COM of clay, by grouping the clay atoms and applied the following command. I have this clay surrounded by water molecules in...

02 March 2019 9,054 1 View