25 April 2016 1 3K Report

I want to calculate the sediment delivery ratio(SDR) in a small watershed(area

More Zhengfeng An's questions See All
Is there no general protocol for vaccination study?

Hi, I searched vaccination study to know which MLD50 is suitable for influenza virus study in pubmed. But why every vaccination and challenge conditions are different? Is there no guideline or...

16 January 2021 7,984 3 View

Plaxis V20 water load apply error in analyses?

Recently I have been working in some embankment project and plaxis V20 is the FEM software I am using to calculate. But by the time I am working, I figured out the water load sometimes applied to...

27 October 2020 7,835 1 View

Is there any mathematical way to represent any function on a z=0 plane transform into an arbitrary differentiable continuous non-linear plane?

Dear scholars, I am now struggling on a question. Let's assume that there is a given line or a given arbitrary function defined on a z=0 plane. Now I twist the plane into a non-linear 3D surface...

03 June 2020 3,693 1 View

Is it OK culture E.coli at RT for overnight?

For plasmid DNA isolation, E.coli was incubated last night. But incubator doesn't work and I just knew it this morning. The incubator fixed now. Is it okay for my experiment?

28 April 2020 2,931 10 View

Where can I get a reliable list of Wieser's (1953) nematode feeding type classification?

Numerous articles cite it but nobody seems to provide an actual list of the taxa and which of teh four groups they are assigned to.

21 March 2020 5,990 5 View

What solvent should I use with SPE to elute amines from silica?

Hello, I am extracting polar compounds from organic samples using SPE. After loading the sample, I use pure methanol to elute the polars. However, I believe alkyl amines are being retained on the...

26 September 2019 854 3 View

Do you have the matlab code of linear canonical transforms ?

I want some MATLAB code about linear canonical transforms in signal processing. Because I research this problem for my subject, I want to know basic way by MATLAB code. This is my first time to...

13 September 2019 9,746 3 View

Acquisition and tracking of BOC signal in multipath environment?

I want some MATLAB code about acquisition and tracking of BOC signals. Because I research this problem for my subject, I want to know basic way by MATLAB code. This is my first time to get this...

15 August 2019 652 2 View

Dear all, I have a question concerning executive function. What does Executive Function inlcude? What tools can be used to assess EF?

My study is going to compare ASD and TD group on their performance in different linguistic items. Do I need to match them on EF? Why or why not?

04 July 2019 8,770 3 View

Progress in integrated utilization of solar energy (Especially for sorption technologies)?

Utilization of solar energy is always one of the meaningful research areas. But most researches are about one or two utilization aspects, such as for cooling, heating, heat storage, power...

03 June 2019 6,983 2 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close