Does anyone has a good protocol for attach antibodies/proteins in silica/glass plates?

Guilherme Marcondes @Guilherme_Marcondes

06 June 2014 1 3K Report

Most of the protocols i've found on papers about attach proteins in glass has some extreme variations about the process... My goal is to attach proteins labelled with FITC in glass plates and establish a negative control that i will attach the labelled proteins directly onto the plate. Can anyone help me with this?

Steingrimur Stefansson

Hi Guilherme,

I have done quite a bit of protein attachment to glass.

I am not sure what you are planning to do, but you can elaborate on this forum or contact me through RG.

Badges
Science method

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Have someone successfully used the ER alpha (Santa Cruz sc-8002) antibody in immunostaining ?

Santa Cruz now recommends this new antibody (F-10) but I can't find a publication using this reference. I'm working on human et non human primate hypothalamus and so far, it doesn't work. Is...

02 March 2021 10,003 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Does anyone know an alternative product for cardiac Troponin T antibody for Immunofluorescence (Thermo # MA512960)?

We have been using Thermo Fisher anti-cardiac Troponin T antibody for immunofluorescence staining in FFPE mouse heart sections but it was recently discontinued. The literature shows it to be the...

01 March 2021 4,937 1 View

Why might my GFP tag be dissociating from my plasmid after transfection?

I have a set of stably transfected cell lines all transfected with plasmids containing GFP tags on the C terminus. During a western blot using anti-GFP antibody, one of my plasmids has dissociated...

01 March 2021 9,310 4 View

No title

Does anyone have the experience of using Taq Man probes in the QIAGEN Rotar- Gene qPCR machine?

01 March 2021 5,311 1 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View