conditions to be considered for modeling a wave guiding structures, how to write matlab codes for modeling, assumptions to be considered for modeling an electromagnetic wave guiding structure
i want to annihilate cross-pivot elements of coupling matrix by using similarity transforms. while doing this, the previously annihilated elements are affected. In this case how to proceed with...
02 March 2018 5,348 0 View
I have an elliptic low pass filter of order 5. it gives three transmission zeros at finite frequencies. i want to arrive at the coupling matrix for this filter. how to determine the topology for...
01 February 2018 1,988 6 View
Thanks in advance
10 November 2017 7,312 0 View
how to annihilate an element, Mik in coupling matrix by using similarity transform when there is no common node j to both i and k. How to take the rotation angle for annihilating this element? the...
10 November 2017 2,956 0 View
can anybody tell how to analyse a S parameter graph for transmission zeros in case of a filter. thanks in advance
06 July 2016 741 0 View
while applying FDTD to a microstrip line , how to do with PML conditions. how to consider with equations at the edges of the strip? in sullivan , g(i,j,k)1..2..3 are considered for the normal...
03 April 2016 1,936 1 View
i am getting the following when i run a matlab code: Error using surf (line 57)While setting the 'ZData' property of Surface:Value must be a scalar, vector or array of numeric type can anybody...
03 April 2016 6,572 3 View
Computational Electromagnetics
31 December 2015 3,991 6 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...
04 August 2024 4,130 4 View