Hello fellow researcher .. What is the meaning of your name?

I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.

03 March 2021 5,266 4 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Which is better medicine or food in obesity?

Preference in terms of the scientific aspect

28 February 2021 796 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

How to find natural frequency of a bridge from vehicle induced vibrations?

i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...

22 February 2021 10,004 3 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

Purification of proteins from baculovirus-infected insect cells?

18 February 2021 6,665 6 View

Small displacement measurement in vacuum?

Hello, I have a question. there is a circular thin foil which vibrates in vacuum, the foil restricted and moves up and down. it is like a diaphragm between two pipes . both sides are in vacuum but...

18 February 2021 8,075 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View