03 March 2022 0 6K Report

Optimaly the 42CrMo4 should be Heat treated the following way:

840°C Austenized

180°C tempered for 2 h

More Leo Mißler's questions See All
What are the ice water bath conditions for the oxidation synthesis method?

The bulk-quantity 1D PANI nanowire/tubes were prepared as follows: analytical grade aniline (4 mmol) and tartaricacid (1 mmol) were dispersed in 10 mL of deionized water at room temperature with...

14 March 2024 4,316 2 View

What is Exactly Triangulation in Educational Research?

How can we execute it in different methods of Educational Research

22 October 2023 9,888 28 View

SPRI bead clean up post Indexing PCR Step in NGS Library Generation?

I have been making NGS and WGBS Libraries for a while now and keep noticing an odd trend with my SPRI beads at the Indexing PCR step. When I go to elute my final Library off the SPRI beads, the...

19 June 2023 8,894 3 View

Is ResearchGate now blocked in China?

Until recently I had no problems accessing RG from the mainland, but currently if appears to be blocked. Is it just me or my specific location?

26 February 2023 2,737 4 View

Why is my coin cell not able to hold its charge and discharge after initial first charge?

The practical calculated capacity of my coin cell LiCoO2/graphite is 0.640mAh. The electrolyte used is 1M LiPF6 in 1:1 EC/DEC. Immediately after assembling the cell, I charge at a given current...

17 February 2023 6,324 1 View

Can you identify the genus of this chironomidae larvae from french Guyane (neotropical genus) ?

Hello community, i'm working on Chironomidae (diptera) from french Guyana and i found one that i can't identify because the larvae didn't correspond at any genus already known and present in...

26 January 2023 8,461 4 View

How to couple FSI (Fluid structure interaction) with electric field in COMSOL?

I want to investigate the interaction between an electret (fluttering in the wind) and a nearby electrode. So the fluttering motion is both affected by the flow and electric field between the...

24 November 2022 9,289 0 View

How can i covert sequence data from FASTA to a VCF format?

Hi!, I am trying to figure out the connectivity between subpopulations of a parrotfish species along the coast of western Africa by analyzing the differences of neutral mutations in SNPs in the...

13 July 2022 8,670 3 View

Possible reasons for AKTA Pure 25 MonoQ column giving high fluctuating pressure?

Hi everyone, Over the past few months the pre and delta column pressure when using our monoQ column has steadily been increasing, and now we've had to reduce our flow rate to 1/4 normal rate to...

05 July 2022 1,132 0 View

Way higher than expected Bonding energy of two carboxylic acids, is it normal ?

Hi ! I'm studying a Heme-Heme dimer (see sketch, chemdraw structure is one Heme ring) and I want to compare the energy of before and after complexation of the propionic acid side-chain to an...

12 June 2022 6,720 1 View

Similar questions and discussions
How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

What is the role of oxidative stress in toxin-induced carcinogenesis?

What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...

02 August 2024 3,174 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Seeking recommendations for equipment to mimic sunlight and heat up a greenhouse system?m?

I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...

28 July 2024 4,006 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close