Is the Topology of a phylogenetic tree same from different tools?

I am very new to bioinformatics. Here,i am trying to make a phylogeny reconstruction of protein sequences following methods like Maximum likelihood (MEGA 6.0 and GARLI) and Bayesian inference...

10 November 2015 4,065 15 View

Any advice on genome-wide screening of homologs?

08 September 2015 8,368 3 View

Does anyone have experience in isolating cell organelles from yeast S. cerevisiae using glass bead beater?

Many use enzymes like lyticase to get spheroplasts and subsequently, perform mechanical disruption to disrupt the yeasts cells. The isolation is usually followed by the centrifugation. Apparently,...

11 December 2014 1,701 2 View

What is the best way to study the structure of different proteins - Bioinformatics?

07 August 2014 2,564 6 View

Can anyone help with membrane reconstitution of enzymes?

I would like to know some probabilities in working with the enzymes in the membranous sources such as liposomes. I am working with a bacterial enzyme which is inactive in its monomeric state. It...

05 June 2014 5,056 4 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Onset of Photo Oxidation in Polymers?

Hi! I am looking for some specific information in regards to the minimum amount of UV intensity required to begin the photo degradation process in polymers. I understand each polymer is...

15 February 2021 7,703 4 View

How can I calculate teh crystallinity degree of graphene oxide?

I had treat my XRD diffraction pattern by Highscore to calculate the crystallinity degree Xc and I have the formula but I dont no the 2Theta of Ac and Aa to calculate Xc. Is it like polymers...

10 February 2021 6,305 5 View

Could any one help me with mechanical properties of CFRP(carbon fiber reinforced polymers)?

I am modeling CFRP laminated a concrete column in Abaqus And I need Elastic and plastic properties of CFRP

09 February 2021 4,930 5 View

Dear colleagues. How can we implement the kinetics of the polymerization of aromatic amines in easier and simpler ways?

Dear colleagues. How can we implement the kinetics of the polymerization of aromatic amines in easier and simpler ways? Are there simpler methods for Nano polymers (other than those obtained with...

09 February 2021 5,783 3 View

How to calculate enthalpy of formation of Polymers taking into account the terminal end groups?

I am trying to find methods for theoretical calculation of enthalpy of formation of Polymers. till now I have found the oligomeric method (Gaussian) which uses the extrapolation of results from...

05 February 2021 9,707 4 View

What are advantages of NELF model?

I am trying to simulate permeation of gases in polymers. For this reson normally i use the clasic models like dual sorption model but newly i foun dthe non equilibrium lattice fluid model. It...

03 February 2021 1,203 3 View

Is it possible to find out the wettability and contact angle of water on the rough or corrugated substrate?

First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...

03 February 2021 9,085 4 View