Here is a thin section of the alteration and XRF + MEB analyses.
Dear Mr. Pelletier,
I attach a review where all environments of alunite and APS minerals are dealt with.
With best regards
H.G.Dill
Hi Harald,
Hi Anicet,
Thanks again for your great contribution.
You cannot imagine how much this information is precious.
Evolution is built on people like you.
Best Regard,
Josh
You can find formed from supergene weathering of sulphide deposits.
All the best
Yes, Dr. Hyseni and Jocelyn, Thank you, this is what I have mentioned and documented in my contribution 4 days ago (see above). Best regards, Anicet
I would like to evaluate the effectiveness of Case Study Approach on the Achievement of college students in Learning Contemporary World.
07 November 2019 7,458 2 View
I'm working on MIC determination using cell culture coated 96 well plate (NUNC Catalogue no. 167008) and just wonder if this will make any difference with using normal untreated plate? I'm dealing...
08 March 2019 8,398 5 View
I have been working on EE studies for my liposomal drug. Size of the particle is around 70-100nm and I measure my drug concentration using UV-Vis method. I have tried centrifuging at ~17,000g for...
26 January 2019 7,088 14 View
Hello all. I am trying to do ChIP-seq with testis tissue, and I have been having a lot of trouble with sorting out my shearing conditions. Essentially, my sheared and unsheared chromatin always...
10 October 2018 3,474 2 View
DNA bisulfite sequencing primer problems
27 March 2018 2,089 1 View
23 January 2017 3,448 3 View
Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...
02 March 2021 4,119 3 View
I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...
22 February 2021 1,400 4 View
I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...
22 February 2021 5,324 3 View
I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...
18 February 2021 5,319 3 View
A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...
13 February 2021 1,245 1 View
I need to spin a 120um thick film. My current procedure consists of spinning the polymer (about 20um), uv exposure, plasma etch, and then spinning another 20um thick layer, uv again, plasma etch...
10 February 2021 2,055 6 View
I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...
09 February 2021 375 2 View
First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...
03 February 2021 9,085 4 View
Due to their ubiquitous nature, there is a tendency of the presence of microbes in a given mineral(s). For instance, if microorganisms that love the of pH less than 6 in the pH value, is isolated...
03 February 2021 4,630 10 View
I know that this is a very difficult question, as the areas of application can vary greatly. However, if you want to operate low as well as high resolution (from a few millimeters to nanometers),...
02 February 2021 4,985 4 View