Determination of weight percentage of copper(I) oxide and copper(II) oxide from XRD data?

More Nitai Chandra Maji's questions See All

How to separate polymer stabilized Cu nanoparticles without centrifugation?

We have prepared highly stable copper sol by the method described in our paper (paper link given below ). Basically here the sub 10 nm nanoparticles are capped with PVP and PEG polymers. We have...

05 June 2017 2,926 3 View

Can anyone help me in providing physical properties of the sample required for DLS Measurement?

I want to measure the DLS size of my sample, which is aqueous colloid of copper particles having size less than 100 nm. During DLS measurement in Malvern Nano ZS90 instruments it is asking for...

08 September 2016 9,228 7 View

How to find the copper content in copper nanopowder?

I have a given sample of copper nanopowder. It contains a residue amount of polymer and all. So how to determine the copper content in the powder? Any method or instrument or procedure?

31 December 2015 1,347 8 View

How do I calculate volume fraction of nanoparticle in nanofluid if it's prepared by one step method?

Nanofluid is prepared by one step chemical reduction method.

05 June 2015 3,760 13 View

What is the mechanism for heat conduction in liquids?

How the heat is conducted through liquid? What is the mechanism? Can you please suggest me papers or book regarding this?

05 June 2015 8,936 4 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ?

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ? and can I use other tubes than Teflon for digestion?

04 July 2024 158 4 View

How do I make a solution from fibroblast growth factor since it is available as a powder?

I am using fibroblast growth factor, purchased in powder form. What suitable substance should be added to get it in a liquid form? Thanks

03 July 2024 9,866 2 View

How to remove aluminium oxide from powder ?

I synthesise intermetallic compounds through nickel and aluminium powders. But the pure powder after synthesis is difficult to obtain. Especially the presence of aluminium oxide very seriously...

01 July 2024 4,030 3 View

Sujoy Sarkar

Reitveld refinement of XRD data is one of the ways to find out the % of phases present in the system.

Nitai Chandra Maji

Thank You Mr. Sujoy. Can you please explain me how to do that? I am attaching the .xrdml and .csv files of my xrd analysis.

Dinesh Kumar

You have to do two phases Reitveld Refinement for finding phase fractions present.