CrystalMaker, Crystaldiffraction, SingleCrystal why separate?

SK M @Sk-M

12 October 2022 0 1K Report

is anyone using these software?

are all 3 needed? (of course for specific purpose they may be)

but which most useful and regularly be needing?

I generally use VESTA, so these seems comparatively has many features.

Any suggestions?

Regards

Badges
Science topic

More SK M's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

What's wrong with my COMSOL model for turbulent flow in time dependent solver?

I am trying to simulate velocity field inside a domain of just ambient air (pressure is 1 atm & velocity is 10 m/s). There is a tank inside it which has a leakage. The leakage hole is leaking...

01 July 2024 2,249 0 View

Why in some degradation experiment the results doesn't fit first or second order kinetics ?

In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...

26 June 2024 6,941 3 View

Why carrier Concentration decreases while increasing Temperature ?

Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...

23 June 2024 4,763 0 View

How to create a crystal in CrystalMaker if you don't know the lattice parameters?

Hi! I'm trying to create crystals in CrystalMaker for new MAX phases. I know the symmetry and coordinates of atoms, but don't know the lattice parameters. What do you do in this situation? Can...

07 October 2022 4,455 0 View

Does anybody know how to convert a CrystalMaker CMDX file format to CMDF?

Older version of SingleCrystal doesn't recognise CMDX file format.

05 June 2022 3,276 3 View

How can I export all information for a crystal structure, in a single file in VESTA or CrystalMaker?

I want to create a data file, including the positions of atoms, bonds, angles, and dihedrals for CH3NH3PbI3 perovskite. Can I do this with VESTA or CrystalMaker?

11 September 2021 7,814 3 View

Can anyone tell me about their experience using the software CrystalMaker, CrystalDiffact and SingleCrystal?

I am contemplating purchasing this software and would like people's opinion.

08 September 2018 2,258 10 View

Can anyone tell me about their experience using the software CrystalMaker, CrystalDiffact and SingleCrystal?

I am contemplating purchasing this software and would like people's opinion.

05 September 2018 5,521 9 View

Can you display screw dislocations in CrystalMaker?

I am just learning CrystalMaker and I am trying to do a screw dislocation. I can make a simple lattice, but I can't quite figure out how to select and move atoms. Any hints?

06 July 2018 6,593 0 View

How to make a heterostructures in Vesta?

Once i got a graphene unite cell in vesta, i import (edit->new phase->import) a MoS2 structure, and in this way i've a heterostructure.That is i am able to save it as file.xyz but i 'm not...

04 May 2017 8,147 8 View

How can I arrange atoms of my PDB file from CrystalMaker software?

Hi, I am performing MD simulations of ZnO nanocluster. I created nanocluster in Material Studio but atoms are not arranged. Can any1 help me to arrange the atoms in PDB file using CrystalMaker...

03 April 2015 2,653 3 View

Free version of CRYSTALMAKER SOFTWARE?

Is free version of CRYSTALMAKER software available for download? I downloaded demo version but that does not allow to save file.

03 April 2015 4,954 2 View

How can I simulate the folded layer of graphene ?

Has anyone done that work? Which kind of software can do that job? Crystalmaker or ? See appendix for reference file. Thank you.

22 March 2015 751 3 View