Creep sometime called plastic flow. The internal mechanism of creep may be due to one or a combination or reasons. What are these reasons?

Nazar K Ali Oukaili @Nazar_Oukaili2

04 April 2017 0 2K Report

interpretation of creep

Badges
Science topic

More Nazar K Ali Oukaili's questions See All

Why the temperature stress in a statically determinate structures corresponds to no change in stress resultant?

equilibrium

03 April 2017 6,535 4 View

Do concrete have relaxation?

Exclude the effect of shrinkage

03 April 2017 3,654 4 View

In vibration analysis of multi-degree of freedom system, what is the value of the off-diagonal elements of the consistent mass matrix?

Vibration analysis

02 March 2017 8,965 0 View

What is the minimum diameter of longitudinal reinforcement of a column?

how many mm?

02 March 2017 4,365 2 View

Is it correct that the value of the prestressing force which calculated by ACI code and AASHTO equals Aps*fpi?

why these codes ignored the effect of the nonprestressed steel and concrete on this value?

01 January 1970 5,429 9 View

What is the time period required to determine the ultimate value of the intrinsic relaxation for steel strands?

how many hours?

01 January 1970 4,931 7 View

What is the degree of the formula used to determine the depth of compression zone in members subjected to axial load and uniaxial bending moment?

columns

01 January 1970 6,250 12 View

How the descending branch of the stress-strain diagram of concrete under uniaxial compression can be determined experimentally?

What type of compression machines shall be used?

01 January 1970 7,178 6 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How can I interpret the data without the need of solving it manually?

How can I interpret the data gathered without solving?

03 August 2024 9,054 3 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to make a Lateral flow control line more uniform?

We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...

31 July 2024 4,510 3 View

Water Consumption in Plastic Recycling: Is it Higher Than for Virgin Plastics?

Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...

29 July 2024 4,630 0 View