How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

Do you think there is cognitive oversaturation in the current pandemic? What impact can this have? And other manifestations?

Dear colleagues, Do you think there is cognitive oversaturation in the current pandemic? What impact can this have? And other manifestations? The question is mainly aimed at adolescents (pupils,...

23 February 2021 7,796 4 View

What is the standard protocol in doing replicates for C. elegans lifespan assay on solid media (thru worm picking)?

I would like to know what is the standard protocol in the number of worms per plate and number of plates per concentration of extract X in a lifespan assay done in solid media and not automated...

23 February 2021 9,933 1 View

What is the possible cause of MSCs low growing?

Hello Everyone, We are inexperienced in culture of MSCs trying to grow a sample from BM of a mare. It is the second time that after preparation of new medium (DMEM-F12 with high glucose - 10% Hy...

07 February 2021 9,989 7 View

What is better to buy a real-time pcr machine or an endpoint?

Hello everyone, we are acquiring a new molecular biology laboratory with the fundamental objective of identifying species of microalgae and cyanobacteria. Perhaps you could help us decide if it is...

24 January 2021 8,320 4 View

How to improve the yield for the reaction below?

I am trying to increase the yield for the reaction below. I did the column and I saw that the major side-product is the symmetric dimer formed by 4-bromobenzyl bromide. I imagine that NaH is...

20 January 2021 7,874 4 View

Is it possible to calculate the energy stored (kWh) in a EV battery by knowing the cathode discharge potential and specific capacity properties?

For example, if I have the following data for a LiNi0,8Co0,15Al0,05O2 compound used in the cathode: - Specific capacity = 200 mAh/g - Average voltage = 3,7 V I have no information about the...

16 January 2021 3,038 2 View

PCR used to work, now it doesn't, why?

I recently did a PCR with certain primers, and the reaction went well for two gels, but when I repeated the exact same reaction a third time it suddenly didnt work, then I did it a 4th time and it...

12 December 2020 364 5 View

Can you suggest a sub-problem and possible objectives regarding to this thesis/research study?

03 November 2020 8,155 3 View

DNA disappears from gel, whats going on?

Recently I've been doing some PCRs and the primes used to work a month ago, but now that we want to repeat the experiment, they are not working anymore. I have noticed something in my gels, and it...

28 October 2020 4,427 4 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

Which is the best silane for making a borosilicate glass surface hydrophobic permanently? and what is the protocol?

Regarding my needs I am looking for a glass coating agent that makes the glass hydrophobic permanently

09 February 2021 3,924 5 View

Is 60%/40% a typical fiber-matrix ratio in vehicle GFRP/CFRP composites?

Quick question I couldn't easily find a definite answer, so I hope someone here could help. I've been looking for information about the ratio (by weight) of glass or carbon fiber to epoxy matrix...

04 February 2021 740 1 View