Can any one explain the meaning of the error message "Domain violation set" in GAMS?

While trying a model GAMS code, i'm getting an error message "Domain Violation Set". I checked the equation codes are correct, but find no clue on the error. Any clarifications? Thanks.

04 May 2019 7,512 1 View

Are wages paid according to labor productivity?

Dear all, As per theory, wage setting occurs based on marginal/average labor productivity. Taking national aggregates of labor & capital, it stands that marginal and average productivity is...

02 March 2018 8,763 3 View

What are the pre-requisites for learning SAM construction & CGE modelling?

09 October 2017 3,789 3 View

How to measure potential output with regard to the output observed?

11 December 2016 2,240 3 View

How terms of trade affects poverty levels?

01 February 2016 6,513 5 View

How to solve these simultaneous equations?

01 February 2015 5,680 2 View

What are the different methods used for impact assessmentof a project ?

Other than the conventional BCR,NPV,IRR and Economic Surplus methods, what are other kinds/methods that one could use in assessing the benefits of a scheme/programme?

31 December 2014 5,220 19 View

How to find out Atkinson Index for different quintiles?

31 December 2014 7,491 7 View

Can someone suggest to me how to observe clusters of states according to poverty status in different NSS years?

10 November 2014 8,234 3 View

How to define land productivity?

Dear all, Option-1: land productivity = value of output / ha of Gross Cropped Area Option-2: land productivity = value of output / ha of Net Sown Area To measure land productivity of a "STATE"...

10 November 2014 5,929 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View