Could anybody please suggest some recent papers on Air Jet Erosion of additive manufactured Ti6Al4V alloy?

Amit Kumar Singh Chauhan @Amit-Chauhan-31

10 September 2018 1 6K Report

My current research area is Air jet erosion of additive manufactured Ti6Al4V alloy. if possible then please send me some papers on Air jet erosion of additive manufactured Ti6Al4V alloy.

Abdullah Alfaify

Hi,

Have a look at the following open-access article:

Article Comparative erosion tests results of titanium alloy Ti-6Al-4...

Good luck with your research,

Badges
Science topic

Similar topics
Mathematics
Algebra
Matrix

More Amit Kumar Singh Chauhan's questions See All

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to do Pre Merger Financial Perfomance Analysis?

For Example, Company A & B merged with Company C , so during the pre merger period there are 3 company so how to do its pre merger analysis with post merger company? (either its 1 to 1 or 3 to 1)

31 July 2024 2,503 3 View

How to estimate a protien's size using Chimera or PyMol? how correct this estimated can be?

I need to know the approximate size of my target protein for Negative-stain EM. I have an alpha-fold predicted structure of the protein. I do not see any turtorial on internet for estimating the...

21 July 2024 5,732 3 View

How to bring baseline to zero for an absorbance data for chromatogram?

I forgot to autozero during the run (Size exclusion chromatography.) and later i realised i forgot to do that and the baseline was not zero but below zero (and in some cases it above zero). I...

15 July 2024 5,551 6 View

How to identify a monomeric protein species of the target without running the molecular weight standard on SEC?

I was using Superose6 10/300 Gl column for purification of my target protein. the sample consists of various oligomeric state and i would like to identify the approximate elution volume where my...

15 July 2024 5,157 2 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

How to properly dilute RNA for cDNA?

Hi all, I have a question regarding proper dilutions and conversions of my RNA. According to my protocol, my cDNA kit is optimized for 1ug of RNA and calls for this amount. I would like to...

07 July 2024 9,206 4 View

Can I use BSA for a Histological Blocking Solution?

Hi all, I would like to know if it is possible to use Bovine Serum Albumin (BSA) in my blocking solution for immunofluorescence muscle fiber typing. The primary antibodies' host is mouse. The...

07 July 2024 7,967 3 View

Potential Vs current density(mA/cm-2) in EC-Lab?

In Zn-Air Battery, how to plot Potential vs current density(mA/cm-2) in EC-Lab softare/BioLogic instrument. Please suggest. plot of the ref....

04 July 2024 3,807 2 View

I am conducting an experiment for oxidative stress assay for C.elegans for a phytochemical and for FUDR needed to added at L1 or L4 stage?

and will i add phytochemical along with FUDR?

28 June 2024 6,254 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What sustainable management strategies can be used to prevent soil erosion and role of biodiversity in sustainable agriculture?

22 July 2024 5,672 4 View

Correct statistical approach for a hermit crab shell exchange experiment?

Hello, I'm planning a shell exchanging experiment with two marine, hermit crab species inside of a tank. I only have one tank available for this experiment. I plan on running 30-40 shell...

20 July 2024 5,676 3 View