Could anybody explain the attached AC IMP result in 5mM Pot. Ferrocynide solution 0.1 m KCl of a modified platinum electrode ?

09 September 2015 0 9K Report

Run The AC impedance of PANi modified platinum electrode the electrolyte solution is 5 mM Pot ferrocynide having 0.1 M KCl and the int Freq is 0.01 Hz to 100 KHz.

Badges
Science topic

More Ashish Kumar Singh's questions See All

How to calculate limit of detection by using procedure of Hubaux and Vos?

Hubaux and Vos article attached herewith bellow. thanking you

05 June 2016 4,737 1 View

Can any one provide a protocol for glutamate decarboxylase (GAD) enzyme assay in mice brain?

Please...

03 April 2016 6,057 2 View

What is the reason for the detachment of electrodeposited PANi/MWCNT film from a platinum disk electrode during washing?

PANI/MWCNT electrodeposition with 50 cycles of CV.

03 April 2015 5,647 5 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

How can a reference point be fixed to an attachment point in Abaqus?

I am currently trying to copy an assembly feature, that is present in an old version of the model I am using, onto a new model. The feature is a reference point that is fixed to an attachment...

16 February 2021 8,872 2 View

Is there a paper that shows the effect of the thermal conductivity of solid electrolytes on lithium secondary batteries?

I want to know the effect of thermal conductivity characteristics of solid electrolytes on the all-solid battery, but I don't know which paper to refer to. Is there a paper on thermal behavior?

15 February 2021 8,806 2 View