Convergence failure calculating for V = 0.000Volt. How to solve it ?

22 May 2022 0 4K Report

While doing simulation studies of organic solar cells with scaps for CuSCN as hole transport layer, I found a pop up showing convergence failure calculating for V = 0.000volt. what to do?

Badges
Science topic

More Ramabadran C D's questions See All

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

Is it possible to dock more than one drug in the same active site or pocket of a protein to study synergistic/antagonistic/additive properties?

I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...

28 July 2024 7,413 6 View

Are diatom inclusions found in shellfish shells?

Mangroves were reported to eat into limestone atolls like so much cake - but could it have been diatom partnerships at mangrove roots that ate into the rock? If gypsum formation is a clue, how...

12 July 2024 159 2 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,330 0 View

Regarding green consumer behaviour ?

HOW TO WRITE GREEN CONSUMER BEHAVIOUR AS A LITERATURE REVIEW

28 June 2024 2,661 0 View

How to produce homogeneous reference gene bands in Western Blot?

Hello, I have been performing Western Blots to study the protein levels of a rodent skin and muscle sample. However, I have not been able to produce homogenous reference bands. I suspect that...

26 June 2024 5,913 3 View

Can the atomic % and weight% of a doping element decrease with increasing its concentration in the resulting compound? If yes, then how?

I found atomic% and weight % of doping element decreased in the resulting compound on increasing its concentration.

28 May 2024 2,455 2 View

How do I perform a dose response curve and get IC 50 values for herbal extract powder?

I need to find out the desired dose for my poly herbal formulation. Please guide me how to get the figures

12 May 2024 8,290 1 View

Do you think undergraduate teaching via online platforms like zoom is sufficient to teach theory parts of Science subjects?

When I analyzed grades of undergraduates, some course taught via online platforms, their grades are lower than the physical lectures.

11 May 2024 7,475 4 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

Franklin M. Fisher (1983) Disequilibrium Foundations of Equilibrium Economics. How is it estimated now? How is it related SMD results?

Fisher studied if there is an out-of-equilibrium process that rapidly converges to some equilibrium points. He claims that Hahn process has a Lyapounof function and therefore convergent to an...

15 July 2024 1,460 4 View

Warning: convergence tolerance of 1.000000e-06 not reached?

Hola a todos, Me gustaría realizar una consulta con relación al mensaje de advertencia que se muestra en la imagen anexada. Es un mensaje que aparece al inicializar la solución de una simulación...

05 July 2024 974 4 View

Are there any people using biolegend anti- mouse CCR2-BV785?

Hi, I'm working on heart flow cytometry, and I use anti-mouse CCR2-BV785 (biolegend, cat150621) for staining, 20 minutes, 4 degree. But I couldn't see any CCR2+ cells. So I'm not sure if it's...

03 July 2024 3,969 4 View

Convergence problems using opensees and specifically openseespy, what algorithm and system should i use to avoid convergence problems ?

hi im performing IDA for a 30 story consisting of bearing wall system of special shear walls for gravity and lateral resisting system , i usually face convergence problems with that , the walls...

27 June 2024 9,492 0 View

Abaqus 2023 - How to access element - scale for implementing a failure criteria with subroutines (UMAT, USDFLD, UEXTERNALDB, ..) ?

Hi all, I am working on subroutines (UMAT and others) with Abaqus. I would need to calculate the average stress by element to eventually change its Young modulus. How should I implement that...

25 June 2024 5,205 1 View

Abaqus 2023 - How to access element - scale for implementing a failure criteria with subroutines (UMAT, USDFLD, UEXTERNALDB, ..) ?

Hi all, Second question on the same or so topic. I am working on subroutines (UMAT and others) for Abaqus to implement Tsai-Wu failure criteria for non-composite structures (I work on long...

25 June 2024 2,955 1 View

Why my mesh convergence is failing in ABAQUS?

I am doing 2D orthogonal cutting simulation in ABAQUS for aluminum. Reducing mesh size up to 0.08 mm reduces the error to 3% but further reduction leads to increase in error from 3 to 39%. Why I...

23 June 2024 9,080 0 View

Is asymmetric term on y-axis in zero field muSR data usually negative?

I am analyzing the zero field muSR data using kubo-Toyabe function. The fit is not converging. I am noted that the asymmetry term on y-axis is neative beyond certain time. I think this is the...

15 June 2024 2,661 0 View

Can someone introduce an article about the convergence of the temperature parameter for the SPH part in Abaqus software?

For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...

13 June 2024 2,504 0 View