How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

Why am i not getting solid after reacting APTES with salicylaldehyde?

The reaction of APTES with salicylaldehyde in ethanol leads to the formation of imine compound yellow solid which is mention in literature, but I am not getting yellow solid I don't know why? when...

28 February 2021 2,955 2 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

How can I remove bubble in WPU film?

I am trying to prepare water-based polyurethane films. When dried air bubbles were formed and destroys the film homogeneity, then I can't use this for mechanical test because of defects. Is there...

26 January 2021 701 1 View

Any suggestion of free of charge questionnaires that measure mood states?

I need a free of charge and short questionnaire that measures mood states. The questionnaire will be used as in a neuropsychological evaluation study. It is well known that mood states can...

16 January 2021 8,284 4 View

Why IPNI voluntarily abbreviates some people's surnames in their standard forms?

The International Plant Name Index is known for standardising plant scientific names, including the standard forms of authors' names. I heard that one person's standard form may be chosen when...

01 January 2021 1,928 5 View

How to deal with negative factor loadings while performing PCA-MLR to calculate quantitative source contribution in air pollution studies ?

If I am getting some negative values in factor loadings while performing principal component analysis (PCA), then I should use that negative values to calculate daily source contribution using...

22 December 2020 5,248 1 View

What are the source markers of Naphthalene, Acenaphthylene and Acenaphthene in ambient atmosphere ?

Is any article available which reports the sources of these PAHs ?

22 December 2020 8,738 1 View

LINCS warning only with -pme gpu?

Dear all, I recently bought a RTX3080 and was unable to start the NPT and production steps due to lincs warning (my old gtx 1080ti card ran normally, using the same .mpd), I tried several...

18 December 2020 3,333 2 View

What is the relationship between induction machine stator reactance variation and slip?

It is possible to notice, at some three phase induction machine datasheets, that exists a relationship between stator leakeage reactance and slip, that is, the stator leakage reactance increases...

23 November 2020 2,949 3 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View