12 May 2017 1 9K Report

I've come across few articles that suggest that it can be done by using the intensities of the sp2 and sp3 C-H stretching bands but no article has any details on the mathematical procedure. I might be overlooking something pretty trivial but can't seem to figure out what it is. Can anyone help?

More Arani Biswas's questions See All
How to do mono formylation of N,N-diethyl-3-methoxybenzamide?

I have attempted the formylation of the above mentioned compound using a very well reported protocol using secondary Butyl Lithium and TMEDA at - 78 degrees Celsius. I have done it quite a few...

08 February 2021 2,793 2 View

What is the minimum number of cells required for fluorescence in situ hybridization?

I have to perform a FISH experiment with limited number of cells and I am trying to estimate the minimum number of cells required to do FISH. Cells are from mammalian cell line. I failed in doing...

12 January 2021 7,887 1 View

Can you give me some Information about the generation of ROS in marine surface water?

Reactive oxygen species is a very new term i think

23 December 2020 8,416 4 View

Can someone suggest me a wear detection method for a pipe which goes under intense heat and pressure at intervals?

I am looking for a wear detection method for a pipe that goes under intense heat and pressure for short instances at intervals. this process has an average cooldown time of 8 seconds between each...

08 October 2020 3,776 2 View

Single-cell cloning from SkBr3?

Did anyone tried single-cell cloning from SkBr3 cell line. I am failing in growing cells post single cell seeding in wells. Any help is appreciated

27 September 2020 8,762 4 View

What to do when RT PCR becomes positive again after 15-20 days of 1st sample positivity?

We are getting some patients who were initially positive of RT PCR for Covid. But in retesting after 15-20 days or even 20 days after those patients remain still positive. Is it for dead RNA...

17 August 2020 9,552 9 View

How to calculate % sequence identity using Clustal W?

I am calculating % epitope conservation for different mammalian antibodies against zebrafish. I have performed the Clustal W for antigenic peptide used in raising the antibodies against the...

05 August 2020 6,399 5 View

What is the Source of Harmonic Power ?

Consider a sinusoidal supply at fundamental frequency as shown, with a series inductive reactance leading to a bus. Let a diode rectifier load be connected to the bus. The switch Sw for resistive...

24 June 2020 8,175 27 View

What is the best book on Game theory from the perspective of Computer Science and Engineering?

I do not know much about game theory. I am finding a book where different protocols and algorithms of computer science have been analyzed using the concept of game theory.

17 May 2020 4,774 7 View

How can a PhD in interdisciplinary fields can benefit a researcher in job market?

I am a PhD scholar of Humanities and my research is broadly connected to Anthropological studies and framework. I have also published with an Anthropological journal of global repute and looking...

10 May 2020 4,202 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close