Can you help me with superplasticity testing?

Vivek Patel @Vivek-Patel-31

24 June 2014 1 351 Report

I need help for hot tensile testing of aluminium 7075 incuding soecimen size and testing parameters.

Article Microstructural evolution and superplastic behavior in frict...

David Bombač

This will help you:

Superplasticity of the rolled and friction stir processed Al–4.5 Mg–0.35Sc–0.15Zr alloy

DOI: 10.1016/j.msea.2013.10.027

(http://www.sciencedirect.com/science/article/pii/S0921509313011222)

Badges
Science topic

More Vivek Patel's questions See All

Can anyone identify the tick species ?

Can anyone tell me the tick species

13 July 2024 7,146 6 View

How to properly dilute RNA for cDNA?

Hi all, I have a question regarding proper dilutions and conversions of my RNA. According to my protocol, my cDNA kit is optimized for 1ug of RNA and calls for this amount. I would like to...

07 July 2024 9,206 4 View

Can I use BSA for a Histological Blocking Solution?

Hi all, I would like to know if it is possible to use Bovine Serum Albumin (BSA) in my blocking solution for immunofluorescence muscle fiber typing. The primary antibodies' host is mouse. The...

07 July 2024 7,967 3 View

Is Vacation Homes and Vehicle Rentals in India succesful?

Assessing the Feasibility of Vacation Homes and Vehicle Rentals in India In my article, "Assessing the Feasibility of Vacation Homes and Vehicle Rentals in India: Understanding Market Needs,...

03 July 2024 5,535 1 View

How the electron and hole pocket near the fermi level in the band structure affect thermoelectric properties of Topological half-Heusler compound?

How the electron and hole pockets near the fermi level in the band structure affect the thermoelectric properties of the topological half-Heusler compound?

26 June 2024 2,933 0 View

Journal's Impact Factor: Publication or Updated?

There are two scenarios: The Impact Factor at the time an article is published. The Impact Factor after the journal updates its metrics annually based on performance. While being interviewed or...

25 June 2024 7,825 2 View

JCR 2024 Impact Factor Download File-Factors caused decline in IF are?

Why the IF of almost all journals declined so much? For the file download go to https://www.researchgate.net/post/JCR_Impact_Factor_2024-Factors_causes_decline_in_IF

21 June 2024 3,358 0 View

Why PLLA deposited by gap electrospinning lose piezoelectricity?

I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...

17 June 2024 9,763 0 View

Can anyone explain how mobile ions moves inside ploymer electrolytes?

I want to know the exact mechanism behind the motion of ions inside the polymer electrolytes.

13 June 2024 3,489 0 View

What is the difference between uv visible measurment and phocatalytic degradation measurment?

why uv is done and why photocatalytic measurement is done although both use uv radiation

09 June 2024 8,750 1 View

How to calculate the proportions in grams or milliliters of the compounds for 60 mL of SAPO-11 zeolite precursor gel?

It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...

01 July 2024 617 3 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

Why my mesh convergence is failing in ABAQUS?

I am doing 2D orthogonal cutting simulation in ABAQUS for aluminum. Reducing mesh size up to 0.08 mm reduces the error to 3% but further reduction leads to increase in error from 3 to 39%. Why I...

23 June 2024 9,080 0 View

ABAQUS - Face could not be partitioned. How to resolve this error?

I am doing orthogonal machining of aluminum in 2D. However, when partitioning for depth of cut with a sketch on face strategy with a parting line, it says that face could not be partitioned. How...

18 June 2024 8,000 0 View

What is the materials composition of automotibles?

What share is made of steel? Plastics and glass? Aluminum? Iron?

15 June 2024 7,246 2 View

What aluminum alloys are used in piston production?

Interesting and of piston production methods.

27 May 2024 1,112 3 View

Outof Brass,Copper,Gold,Aluminum,Stainless steel,Silver Which is the best material used as meshing material for regenerator while design of cryocoole?

while designing of stirling type pulse tube cryocooler which parameters are considered for meshing material of regenerator? and Out of Brass,Copper,Gold,Aluminum,Stainless steel,Silver Which is...

22 May 2024 3,728 0 View

Where to find Johnson-Cook parameters for pure Zinc?

I am currently simulating the impact of a zinc interlayer between Aluminum workpieces in ABAQUS (Friction stir welding process). While it was easy to find in literature the Johnson-Cook...

21 May 2024 1,643 0 View

Prevent evaporation in hypoxic incubator?

I have noticed massive media evaporation (>50% volume) from culture dishes after 72-96hr inside a Memmert ICO50 hypoxic incubator (Temp: 37C, humidity: 86%, CO2: 5%, O2: 1%). I've confirmed the...

29 April 2024 9,872 1 View

Can PVA be used as an additive in Aluminum Powder for achieving higher Sinter density?

I am an undergrad student and I need to suggest optimum amount of PVA to be added in Aluminum powder for achieving improved sinter density. Your guidance will mean a lot to me. Thanking in...

25 April 2024 4,892 0 View