Can you explain about spectral and thermal sensors that using for detecting drought tolerant cultivars?

More Mohammadreza Pourghayoumi's questions See All

Does anyone know how we can calculate the activity of SOD enzyme?

I measured activity of SOD enzyme with NBT method by Spectrophotometer. SOD (EC 1.15.1.1) activity was determined by measuring its ability to inhibit the photoreduction of nitro bluetetrazolium...

03 April 2016 9,389 22 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

What should a smart water system look like?

Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...

16 February 2021 1,094 3 View

Receiving very less number of hits and events in acoustic emission tests?

I am doing a three point bend test with concrete specimen of dimension 280mm*90mm*90mm. I am putting 2 sensors near the notch with 3cms away from both the sides. the experiment ran for 20 mins but...

13 February 2021 2,990 1 View

How to increase coupling range (distance between reader and sensor coils) in LC resonance circuit?

Hello great researchers, I am working on a wireless pressure monitoring project where sensing part is actually an LC resonance sensor and I am using a planar coil as a reader to get wireless...

11 February 2021 4,148 5 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View

How to eliminate noise when using a sensor with instrumentation amplifier and giving it's output to Arduino?

When I am trying to implement a pressure sensor through instrumentation amplifier and then giving it's output to Arduino, I am getting garbage value due to noise, so how to eliminate it.

05 February 2021 8,598 11 View

Comparing Uniaxial accelerometer sensors activity counts with Triaxial accelerometer (IMU)'s activity counts?

Hi I have to compare the uniaxial sensor(wearable) data with Triaxial sensor data(IMU). The uniaxial sensor output has a single column of activity counts whereas Triaxial sensor(IMU) has three...

05 February 2021 3,999 1 View

Mohammadreza Pourghayoumi

Dear Morteza,

I asked this question in response to the project of Dr Walter in Research Gate.

However, I changed the question.

Thank you for your answer,

Best regards,

Mina Younan

https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4239877/

http://www.ishs.org/ishs-article/618_46

Dear Mina,

Thank you for your useful papers.

Wishing you the best