Can we use multigroup analysis in AMOS to run a moderator variable with more than two categories?

More Nishadi Gampathirana's questions See All

Can we reduce the number of items in a scale to develop unidimensional construct?

The dependant variable of one of my research projects is a higher order construct (Reflective-Formative) which consists with seven sub dimensions and those dimensions are again reflected by 28...

09 June 2023 2,730 3 View

What is the suitable likert scale for a questionnaire, among 5 and 7 points?

One of my research questionnaires has been formulated with 7 point likert scale. Further, the target respondents are adolescents (age between 10-19). What is the suitable likert scale (among 5...

01 January 1970 7,367 8 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Imran Anwar

Nishadi Gampathirana Yes AMOS allows running multigroup analysis (MGA) with three or more categories. You can even use Smart-PLS for MGA. A sample paper checking moderation with three categories using Smart-PLS is attached herewith.

Nishadi Gampathirana

Thank you very much Imran Anwar. Highly appreciate your kind assistance.