Can we mix elemental powders of 325 mesh using an agate mortar and pestle?

B. Srikanth Ragunath @B-Srikanth-Ragunath

05 January 2021 1 8K Report

Elemental Powders like Titanium, vanadium, tungsten, zirconium, hafnium.

B. Srikanth Ragunath

An Giang Nguyen

After mixing the powders the next step will be making them into pellets and annealing them at higher temperatures.

Badges
Science topic

More B. Srikanth Ragunath's questions See All

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

Can any of you suggest how to find the detection limit.?

I am working on flourescence sensing of heavy metals using quantum dots.Can any of you suggest how to find the detection limit. Whether it is calculated from formula or we can get from instrument?

19 July 2024 7,411 3 View

Cloning of flaviviruses is difficult i have noticed that cells loose their transformation ability after cloning fragments inside vector any advice?

As flaviviruses genome is very frequently prone to mutation hence it is very difficult to clone whole genome inside vector what kind of vector and cells can sustain such amount of cloning...

11 July 2024 4,284 0 View

I am not getting proper colonies while ligating one of fragments in my vector the colonies seems to be normal but in light it seems lysed any reason?

I am working on cloning of a gene fragment inside my vector everything we tried to do correctly like making insert and vector with utmost care but after ligation the morphology of colonies seems...

11 July 2024 9,010 3 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

I have a doubt in finding the amount of ferromagnetic and antiferromagnetic contribution in a canted system?

Is it possible to differentiate or calculate, the amount of ferromagnetic and antiferromagnetic contribution in a canted system? (Weakly frustrated canted antiferromagnetic system)

25 June 2024 6,210 0 View

How transmittance is dependent on the band gap and atomic structure?

UV-Visible NIR analysis

20 June 2024 9,056 3 View

Whether size obtained from TEM and XRD should be equal?

I have got crystalline size around 15nm from xrd but TEM is giving particle size 4nm

20 June 2024 6,064 8 View

If I dop a metal ion into the ternary nanoparticles can I call it as heterostructure?

Ag+ ion replaced some of the Cu+ ion. ie, Ag+ is the dopant

14 June 2024 2,814 1 View

Whether the same synthesised inorganic nanoparticle show different heavy metal sensing by flourescence?

14 June 2024 7,373 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ?

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ? and can I use other tubes than Teflon for digestion?

04 July 2024 158 4 View

How do I make a solution from fibroblast growth factor since it is available as a powder?

I am using fibroblast growth factor, purchased in powder form. What suitable substance should be added to get it in a liquid form? Thanks

03 July 2024 9,866 2 View